Control Arm Set / 控制臂組裝 - THUNDER TIGER TITAN X50 Instruction Manual

Control Arm Set / 控制臂組裝
Bag G+J
No. Material No. Description
1
BK2248 PHASING CONTROL TRACK
2 BK2249 CANOPY RETAINING POST
3 HME3-18B SET SCREW,M3x18
4 HMC2-4B SOCKET SRCEW,M2x4
5
BK2271 GYRO TRAY
6
HNX3-12B S.B.H SELF TAPPING SCREW
BV2538-1
120°CONTROL ARM SET-R, 4756
7*
BV2569-R
120° FB CONTROL ARM SET-R, 4757
BV2539-1
120° CONTROL ARM SET-L, 4756
8*
BV2570-L
120° FB CONTROL ARM SET-L, 4757
9 BK2279 HEX POST
HME3-18B
SET SCREW,M3x18
無頭內六角螺絲,M3x18
HMC2-4B
SOCKET SRCEW,M2x4
內六角螺絲,M2x4
HNX3-12B
S.B.H SELF TAPPING SCREW
半圓頭內六角自攻螺絲
HMC3-12B
SOCKET SCREW,M3x12
內六角螺絲,M3x12
HMM25Z
NYLON NUT,M2.5
止鬆螺帽,M2.5
BK0077
COLLAR,d3xD4xW6
軸環,d3xD4xW6
The hole with a round chamfer
goes toward the tail。
有倒角的孔徑朝向尾座。
(16)
(17)
1. Attach the Bearing into the Rubber Bearing Support.
2. Screw the Shaft End onto the Tail Drive Shaft with a drop of threadlocker
as the drawing, but do not over tighten.
3. Add a drop of thin CA glue on the Tail Drive Shaft next to where the
bearing should be, and then slide the bearings over the position quickly;
the distance from the Shaft Drive End to the Rubber Shaft Bearing
Support is approx. 350mm / 13.78".
4. Apply some amount of silicon oil or Vaseline onto the rubber surface for
easy install into the tail boom later.
All manuals and user guides at all-guides.com
Qty
名稱
相位控制導軌
機殼固定鋁柱
無頭內六角螺絲,M3x18
內六角螺絲,M2x4
陀螺儀座
半圓頭內六角自攻螺絲
120° 金屬控制搖臂(右), 4756
120° 無平衡翼控制搖臂組(右), 4757
120° 金屬控制搖臂(左), 4756
120° 無平衡翼控制搖臂組(左), 4757
內六角連接頭
BK0649-1
LINKAGE BALL
(1)
內六角連接頭螺絲
(5)
(6)
(3)
(2)
(4) (9)
(10)
(11)
(13)
(7*)
(10)
Right Side
(12)
右側
Tail
尾座
(18)
(19)
Apply C.A Glue
使用快乾膠黏合
Apply threadlocker
使用螺絲防鬆膠
No. Material No. Description
10
1 BK0649-1 LINKAGE BALL
11 BK0088 WASHER, d3xD5xW0.5
2
12 BK0077 COLLAR, d3xD4xW6
2
2 13 HSA3-10 BUTTON HEAD SOCKET SCREW, M3x10
14
1 BK2552 TAIL DRIVE SHAFT
15
4 BK0367 TAIL DRIVE SHAFT LINKER
16 BK2529 TAIL DRIVE SHAFT BRG
1
1 17 HMV1680ZZY BEARING, d8xD16xW5
1 18 HMC2512B SOCKET SCREW,M3x12
19
1 HMM25Z NYLON NUT,M2.5
2
Secure all screws shown on this page with a drop of
thredlocker except the screws #4 and 6.
除螺絲＃4及6之外，本頁顯示之螺絲請使用適量防鬆膠鎖固。
(6)
Note the "120L"/"120R" mark on the arms.
請按照控制臂左、右方向安裝。
(14)
1. 將軸承擠壓入橡膠軸套內。
2. 參考圖示，塗抹些許防鬆膠將尾傳動軸接頭
鎖在尾傳動軸，但勿過度鎖緊。
3. 在尾傳動軸上軸承固定位置前方，塗抹少量
快乾膠，迅速滑動軸承至定位固定；該定位
大約距離軸傳動接頭350mm / 13.78"處。
4. 塗抹些許矽膠油脂或凡士林於橡膠軸套表面
上，稍後將尾驅動軸組裝入尾管時，會較為
容易。
-17-
名稱
內六角連接頭螺絲
墊片, d3xD5xW0.5
軸環, d3xD4xW6
半圓頭內六角螺絲, M3x10
尾驅動軸
尾驅動連接棒
傳動軸軸承套
滾珠軸承, d8xD16xW5
內六角螺絲, M2.5x12
止鬆螺帽, M2.5
(2)
(3)
(4)
(8*) Left Side
左側
(13)
(9)
(11)
CA
(19)
CA
(18)
Qty
4
2
2
2
1
2
1
1
2
2
(10)
(10)
(12)
(15)
Nose
機頭