Related Manuals for Ice-O-Matic Series 250 through 2306
Summary of Contents for Ice-O-Matic Series 250 through 2306
- Page 1 Installation, Start-Up and Maintenance Manual EF and EMF Flaked Ice Machines Series 250 through 2306 ICE-O-Matic 11100 East 45th Ave Denver, Colorado 80239 Part Number 9081178-01 Date 1/06 Rev. C...
- Page 3 EMF Series flake ice machines. Do not attempt to perform installation, start-up or maintenance unless you have read and fully understand this manual. If, at any time, you encounter conditions that are not addressed in this manual, call, E-mail or write the ICE-O-Matic Service Department: ICE-O-Matic 11100 E.
-
Page 4: Table Of Contents
EF and EMF Series Forward Table of Contents Freight Claim Procedure Warranty Model Number and Serial Number Format Installation Guidelines Remote Condenser Guidelines Electrical and Plumbing Requirements How the Machine Works Start-Up Procedure General Maintenance Cleaning Procedure Cabinet Care Winterizing Procedure Maintenance Record Page ii Table of Contents... -
Page 5: Freight Claim Procedure
If loss or damage does not appear until merchandise has been unpacked, make a written request for inspection by the carrier within 15 days of the delivery date. Then file a claim on a form from the carrier. File Claim Without Delay Do Not Return Damaged Merchandise to ICE-O-Matic Page iii... -
Page 6: Warranty
Domestic & International Warranty Mile High Equipment Company (the “Company”) warrants Ice-O-Matic brand ice machines, ice dispensers, remote condensers, and ice storage bins to the original user customer against defects in material and factory workmanship for a period of thirty-six(36) months on cube ice machines and twenty-four (24) months on flake ice machines, “compressed ice”... -
Page 7: Model Number And Serial Number Format
Series: Environmental Modular Flaker (Uses HFC Refrigerant) This format is 14 characters long and begins with a date code followed by the ICE-O-Matic identifier, and then a sequential number. This is an entirely numerical serial number. The new serial number will look like the example. -
Page 8: Installation Guidelines
Installation Guidelines Installation Guidelines For proper operation of the ICE-O-Matic ice machine, the following installation guidelines must be followed. Failure to do so may result in loss of production capacity, premature part failures, and may void all warranties. Reference the installation parameters prior to installing the machine: Ambient Operating Temperatures Minimum Operating Temperature: 50°F (10°C) -
Page 9: Installation Guidelines
If the ice machine is to be mounted on a bin or dispenser other than an ICE-O-Matic, refer to the manufacturer’s instructions for machine mounting. ICE-O-Matic will not be responsible for damage or injury that results from unexpected closing of the bin door as a result of the ice machine being too far forward on the bin. -
Page 10: Remote Condenser Guidelines
EF and EMF Series Remote Condenser Installation For proper operation of the ICE-O-Matic ice machine, the following installation guidelines must be followed. Failure to do so may result in loss of production capacity, premature part failure, and may void all warranties. - Page 11 100 foot line set run. For proper operation of the ICE-O-Matic ice machine, the following installation guidelines must be followed. Failure to do so may result in loss of production capacity, premature part failure, and may void all warranties.
-
Page 12: Electrical And Plumbing Requirements
EF and EMF Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: 32, 38 and 48 inch Cabinets TOP VIEW ICE-O-MATIC FRONT VIEW SIDE VIEW REAR VIEW Page 6... - Page 13 EF and EMF Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: EMF 400, 800 1000 Air, Water and Remote Page 7...
- Page 14 EF and EMF Series Electrical and Plumbing Requirements Electrical and Plumbing Requirements: EMF2300 Air, Water and Remote Page 8...
-
Page 15: How The Machine Works
EF and EMF Series A general description of how the ICE-O-Matic Flaker works is given below: Whenever the ON/OFF switch is in the ON position (and the bin control and safety controls are closed) the machine will continuously make ice and deliver it into the storage bin. -
Page 16: Start-Up Procedure
EF and EMF Series Please Follow These Instructions Carefully ● Check the auger assembly to insure that it turns freely. Turning the large pulley of the gear reducer should require only slight finger pressure. ●Check that the condenser fan turns freely. ●Remove tape and packing from the float valve and reservoir ●Before turning the water supply on, check the low temperature safety control for proper operation:... - Page 17 EF and EMF Series ●Check bin control for proper operation The bin control is used to shut the machine off when the bin fills with ice. The bin control must be checked upon installation or initial start-up and when performing maintenance. Adjustments are not covered under warranty. With the machine running and making ice, hold ice against the brass thermal well that houses the bin control capillary tube.
-
Page 18: General Maintenance
EF and EMF Series Electrical shock and/or injury from moving parts inside this machine can cause serious injury. Disconnect electrical supply to machine prior to performing any adjustments or repairs. Failure to perform the required maintenance at the frequency specified will void warranty coverage in the event of a related failure. -
Page 19: Cleaning Procedure
EF and EMF Series CAUTION: Protective eyewear and gloves should be worn when using cleaning products. CLEANING AND SANITIZING INSTRUCTIONS 1. Turn the machine and water supply to the float off. 2. Remove or melt all ice in the bin. 3. -
Page 20: Cabinet Care
EF and EMF Series Cleaning stainless steel Commercial grades of stainless steel are susceptible to rusting if not properly maintained. It is important that you properly care for the stainless steel surfaces of your ice machine and bin to avoid the possibility of rust or corrosion. Use the following recommended guidelines for keeping your stainless steel looking like new: 1. -
Page 21: Winterizing Procedure
EF and EMF Series Winterizing Procedures Important! Whenever the ice machine is taken out of operation during the winter months, the procedure below must be performed. Failure to do so may cause serious damage and will void all warranties. 1. Turn off water to machine. 2. -
Page 22: Maintenance Record
EF and EMF Series Service History Service History Model Number__________________Serial Number__________________Date Installed__________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________...
Need help?
Do you have a question about the Series 250 through 2306 and is the answer not in the manual?
Questions and answers