Related Manuals for Ice-O-Matic ICEU060
Summary of Contents for Ice-O-Matic ICEU060
- Page 1 SERVICE AND INSTALLATION MANUAL ICE UNDERCOUNTER SERIES CUBERS MODEL-ICEU060 Mile High Equipment 11100 East 45th Ave Denver, Colorado 80239 Part Number 9081291-01 Print Date 11/01...
-
Page 2: Table Of Contents
Keep this manual for future reference. Ice-O-Matic 11100 E. 45 Ave. Denver, Co. 80239 800-423-3367 The ICEU060 Service Parts Manual is available separately, Part Number 9081291-02 Table of Contents Page 1 ICEU060 Page 1 Page 2 Page 3-5... -
Page 3: Specifications/Limitations
Specifications and design are subject to change without notice. The ICEU060 ice machine has a 3 year Parts Warranty and a 3 year Labor Warranty. The Compressor and Evaporator have a 5 year Parts Warranty Ice-O-Matic recommends the installation of water filters. -
Page 4: Installation
Installation ICEU060 Location: Prior consideration for the location of the ice machine shall include: Installation location to be indoors with a minimum room temperature of 50°F and with a maximum room temperature of 100°F. The incoming water temperature to the machine should be between 40°F and 100°F. - Page 5 4. The maximum allowable voltage variation should not exceed ten percent of the name plate rating. 5. All external wiring should conform to the National, State, and local electrical code requirements. Usually an electrical permit and the services of a licensed electrician will be required to install the receptacle. Page 4 ICEU060...
-
Page 6: Installation
Installation ICEU060 Final Check: 1. Is the cabinet level? 2. Have all the electrical and piping connection been made? 3. Has the voltage been tested and checked against the nameplate rating? 4. Is the unit plugged into a separate electrical circuit? 5. -
Page 7: Initial Start Up
The icemaker should stop within a few minutes of having ice on that tube. 11. Fill out the Warranty Registration and Customer Evaluation form, and mail both to Ice-O-Matic. 12. Make sure the user understands the operation and maintenance requirements for the icemaker. Leave the service manual and name of the local Ice-O-Matic service agency with the user. -
Page 8: How It Works-Component Description
How It Works ICEU060 Component Description Cube Size Control The Cube size control is located in the front of the control box, behind the front panel. The sensing capillary tube of the cube size control is routed out of the control box into its bulb holder on the evaporator coil. It is a reverse acting temperature control with double throw contacts. -
Page 9: Component Location
Component Location ICEU060 Page 8... -
Page 10: How It Works-Water System
How It Works ICEU060 Water System Freezing Cycle The refrigeration process creates cold temperatures within the evaporator coils and removes heat from the water sprayed up into the inverted ice cube cups. When enough heat is removed, the water changes into ice, and forms where it is the coldest: in the ice cube cups. -
Page 11: How It Works-Refrigeration
How It Works ICEU060 Refrigeration System Freezing Cycle The ice cubes are formed in an inverted mold that is refrigerated. The refrigeration process begins at the compressor. There, refrigerant vapor is compressed and flows from the compressor through the discharge line as a high temperature, high pressure gas. In the discharge line there is a strainer with two outlets;... -
Page 12: Harvest Cycle
How It Works ICEU060 Refrigeration System Harvest Cycle (When the cubes are released) The ice cubes have been formed in an inverted mold that was refrigerated. Now the refrigeration system will change to warm the cube mold and release the cubes. -
Page 13: Operation And Adjustment
1/8 turn at a time until the ice level is correct. Freeze Cycle Time - 20-25 Minutes Defrost Cycle Time – 2-3 Minutes Compressor Amps Freeze Cycle – 3.6 to 4.3 Harvest Cycle – 3.6 to 7.7 Page 12 ICEU060... -
Page 14: Sanitizing And Cleaning
Sanitizing And Cleaning An Ice-O-Matic ice machine represents a sizable investment of time and money in any company’s business. In order to receive the best return for that investment, it MUST receive periodic maintenance. It is the USER’S RESPONSIBILITY to see that the unit is properly maintained. The following is a list of recommended maintenance that will help keep the machine running with a minimum of problems. -
Page 15: Service Diagnosis
Replace the drier and refrigerant. Replace the cube size control. Check water supply. Replace hot gas valve. Replace inlet water valve. Relocate machine or water line. Replace cube size control. Replace hot gas valve. Replace inlet water valve. Clean bin drain. Page 14 ICEU060... -
Page 16: Component Replacement
6. Reverse the removal procedures to reinstall the cube size control. Adjust as necessary. Refrigeration System Any time the refrigeration system is opened, the drier must be replaced, the system evacuated and the exact charge measured into the system. Any other procedure is incorrect and will result in substandard performance. Page 15 ICEU060... -
Page 17: Component Replacement
7. Pull out spray platform, lift pump and disconnect hose. 8. Pull water pump up and out of icemaker. 9. Dismount water pump from cover assembly (retaining brackets), and remount the replacement pump in its place. 10. Reverse removal procedures to replace. Page 16 ICEU060... - Page 18 Component Layout ICEU060 Page 17...
-
Page 19: Wiring Diagram
Wiring Diagram ICEU060 Page 18...