Table of Contents
Advertisement
Quick Links
For Your Records and
Warranty Assistance
For reference, also attach your receipt or a copy
of your receipt to the manual.
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
Form# 42426-01
20100329
©2010 Hunter Fan Co.
Type 2 Models
Type 2 Models
Type 2 Models
Owner's Guide and Installation Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hunter 42426-01
Summary of Contents for Hunter 42426-01
- Page 1 For reference, also attach your receipt or a copy of your receipt to the manual. __________________________________________ Model Name __________________________________________ Model No. __________________________________________ Date Purchased __________________________________________ Where Purchased Form# 42426-01 20100329 ©2010 Hunter Fan Co. Type 2 Models Type 2 Models Type 2 Models Owner’s Guide and Installation Manual...
-
Page 2: Table Of Contents
Fan .......16 11 • Troubleshooting ....17 © 2010 Hunter Fan Company 42426-01 • 03/29/10 • Hunter Fan Company Welcome ®... - Page 3 If you want to use an existing fan site, complete the following checklist to determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page.
- Page 4 You have now successfully prepared your ceiling fan site. For instructions to install your ceiling fan, go to your fan manual and continue with Section 2 • Installing the Ceiling Plate. 42426-01 • 03/29/10 • Hunter Fan Company Steps 2 – 3 Step 4...
- Page 5 Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include instructions for all three Installer’s Choice mounting methods.
-
Page 6: Getting Ready
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •... -
Page 7: Installing The Ceiling Plate
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer 42426-01 • 03/29/10 • Hunter Fan Company For Angled Ceilings: Be sure to orient the ceiling plate so that the two tabs are pointing toward the ceiling peak. -
Page 8: Assembling And Hanging The Fan
3-7. Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. 3-8. Place the slots over the hooks to hang the fan. 42426-01 • 03/29/10 • Hunter Fan Company Standard or Angled Mounting Steps 3-2 – 3-3... -
Page 9: Setting The Remote Transmitter And Receiver
4-3. Install the included 9-volt battery into the transmitter. CAUTION: The remote control device complies with part 15 of the FCC rules. Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment. -
Page 10: Wiring The Fan
Large Wire Connector Small Wire Connector 42426-01 • 03/29/10 • Hunter Fan Company 5 • Wiring the Fan 5 • Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. -
Page 11: Installing The Canopy And Canopy
Note: Should you need to remove the trim ring, press firmly on opposite sides of the trim ring directly above the groove in the hanger ball. The tabs will flex out releasing the canopy trim ring. 42426-01 • 03/29/10 • Hunter Fan Company Step 6-1 Groove... -
Page 12: Assembling The Blades
Blade Assembly Use with grommet Use without grommet Blade Mounting Screw 42426-01 • 03/29/10 • Hunter Fan Company 7 • Assembling the Blades Step 7-1 (Detail) Grommet Screws Step 7-4 Steps 7-1 – 7-2... -
Page 13: Completing Your Installation With A Multi Staked Light Fixture
Switch Housing Step 8-4 42426-01 • 03/29/10 • Hunter Fan Company WARNING: Use only the light fixture supplied with this fan model. 8-1. To attach the upper switch housing, partially install two #6-32 x 3/8” housing assembly screws into the switch housing mounting plate. - Page 14 190 Watts. Exceeding that limit or the marked limit on this product may result in fire hazard or improper operation. 42426-01 • 03/29/10 • Hunter Fan Company Thumbscrews Steps 8-7 – 8-8 Shade...
-
Page 15: Operating The Remote Control And Mounting The Holder
9-4. You can mount the remote holder to any toggle switch plate with the screws already in the switch plate. Or, you can simply mount the remote holder on the wall. 42426-01 • 03/29/10 • Hunter Fan Company Fan Speed High Fan Speed Steps 9-1 –... - Page 16 Turn the fan off and let it come to a complete stop. Slide the reversing switch on the fan to the opposite position. Restart fan. 42426-01 • 03/29/10 • Hunter Fan Company In warm weather, use downward air flow pattern...
-
Page 17: Troubleshooting
1. Turn the power to the fan off at the wall switch. Wait 30 seconds, then resume power to the fan. 42426-01 • 03/29/10 • Hunter Fan Company 11 • Troubleshooting If you need parts or service assistance, please call...
Need help?
Do you have a question about the 42426-01 and is the answer not in the manual?
Questions and answers