Advertisement
Widescreen monitor
／寬屏顯示器
How to reset your monitor
／如何重設顯示器
Remote controller —
Installing the lithium coin battery (CR2025)
Warning:
• Do not install any battery other than CR2025 or its equivalent; otherwise, it
may explode.
• Store the battery in a place where children cannot reach to avoid risk of
accident.
• To prevent the battery from over-heating, cracking, or starting a fire:
– Do not recharge, short, disassemble, or heat the battery or dispose of it in
– Do not leave the battery with other metallic materials.
– Do not poke the battery with tweezers or similar tools.
– Wrap the battery with tape and insulate when throwing away or saving it.
Before using the remote controller
Remote sensor
• Aim the remote controller directly at the remote sensor on the monitor. Make
遙感器
sure there is no obstacle in between.
• Do not expose the remote sensor to strong light (direct sunlight or artificial
lighting).
Main elements and features
／主要組成部分及作用
MONITOR CONTROL
1
2 MODE button
3 ASPECT button
4 MENU button
5
DVD/RECEIVER CONTROL
6 Receiver control buttons
Basic operations
／基本操作
Preparation
Before operating the unit, make sure that all external components are correctly connected and
installed.
CAUTION:
• When not in use, close the liquid crystal panel and store it into the compartment; otherwise it may obstruct
the visibility through the rearview mirror.
• Do not touch the surface of the liquid crystal panel directly.
1
1
This will reset the microcomputer. Your preset adjustments will also be erased.
此操作將會重設微處理器。您所做的預設調整也會被清除。
—
／遙控器
RM-RK230
RM-RK230
CR2025
／安裝鈕扣型鋰電池（
a fire.
／在使用遙控器之前
(standby/on) button
• Turns on the power if pressed.
• Turns off the power if pressed and held.
• Selects the playback source.
• Changes the aspect ratio of the screen.
• Calls up the menu, then selects the adjustable menu items.
/
buttons
• Adjust the level of the selected item or select an appropriate setting for
selected item.
Controllable only if your car receiver which is connected to this monitor is
one of the JVC receivers.
Open the liquid crystal panel.
Press PUSH-OPEN button until the liquid crystal panel is unlocked, then
open the liquid crystal panel by both hands.
When closing the liquid crystal panel, store it in the screen compartment until it
is locked.
To change the monitor position
／如何切換顯示器位置
You can select four positions from the three
positions.
1
Slide the arm lock lever to RELEASE, then
pull down or push up the monitor.
2
Slide the arm lock lever to HOLD, then
remove the screen arm to the nearest
locked position.
您可以從以下四個位置中選擇一個適當的顯示器位置。
1 將支撐臂鎖鎖桿滑至
RELEASE
，然後拉下或推
起顯示器。
2 將支撐臂鎖鎖桿滑至
HOLD
，然後將螢幕支撐臂
移至最近的鎖定位置。
1
(standby/on) button
• Turns on the power if pressed.
• Turns off the power if pressed and held.
2 Remote sensor
3 Dome light switch
See "To activate the door sensor" on page 3.
4 IR transmitters
5 Dome lights
6 Arm lock lever
7 Reset button
8 Screen (Liquid crystal panel)
9 White LED
p PUSH-OPEN button
q Screen compartment
w Screen arm
When you watch the screen at an angle, the picture might not be clear. This is not a malfunction. The finest
picture can be seen when you watch the screen straight-on.
當您以某個角度觀看螢幕時，圖像可能不清晰。此非故障。正面觀看螢幕時可看到最佳圖像。
）
警告
•
切勿安裝
•
請將電池存放在兒童無法拿到的地方，以避免事故發生的危險。
•
為防止電池過熱，炸裂或引起火災：
–
切勿為電池充電，使電池短路，分解電池或加熱電池或將其扔置於火中。
–
切勿將電池與其它金屬物質放在一起。
–
切勿用鑷子或類似的工具穿刺電池。
–
要廢棄或保存電池時，請用膠帶纏繞並使其處於絕緣狀態。
•
將遙控器直接對準本機上的遙感器。確保兩者之間沒有障礙物。
•
切勿將遙感器暴露於強光照射處（直射的陽光或人工光線）。
顯示器控制
1
（待機／開機）鍵
•
若短暫地按則啟動電源。
•
若按住則關閉電源。
2 MODE
•
選擇播放源。
3 ASPECT
•
切換螢幕的縱橫比。
4 MENU
•
調出菜單，然後選擇可調整菜單項目。
5
/
•
調整所選項目水平或為所選項目選擇適當的設定。
DVD
／接收機控制
6
接收機控制鍵
僅在與顯示器相連接的汽車接收機為
操作前注意事項
在操作顯示器系統之前，確保所有外接設備已正確連接和安裝完畢。
注意：
•
不使用時，請關上液晶面板並保存在收藏櫥內；否則會妨礙後視鏡的視野。
•
切勿直接觸摸液晶顯示面板表面。
1
打開液晶面板。
按 PUSH-OPEN 鍵直到打開液晶面板鎖，然後用雙手將液晶面板拉開。
關閉液晶面板時，將其保存在螢幕收藏櫥內直到鎖定液晶面板。
To be continued....
2
1
（待機／開機）鍵
•
若短暫地按則啟動電源。
•
若按住則關閉電源。
2
遙感器
3
圓頂燈開關
3
參閱第
頁的"如何啟動門禁感應器"。
4
紅外線發射器
5
圓頂燈
6
支撐臂鎖桿
7
重設鍵
8
螢幕（液晶面板）
9
LED
白色
p PUSH-OPEN
鍵
q
螢幕收藏櫥
w
螢幕支撐臂
CR2025
或同種類型以外的電池，否則將引起炸裂。
鍵
鍵
鍵
鍵
JVC
接收機時才可如此操作。
When closing the liquid
crystal panel, push up
the monitor to the highest
position.
關閉液晶面板時，將顯示器推至
最高位置。
續
....
Advertisement
