Advertisement
Quick Links
WARNING
・The supplied connecter may not connect securely to disc grinders. In this case, do not use TORNADO.
・TORNADO is for use when cutting concrete, stone and brick. Do not use when cutting metal or other materials.
Do not use with any other type of cutter, such as a grindstone or tipped saw.
・Always check TORNADO for damage, cracks or deformation before use.
Do not use TORNADO which is damaged, cracked or bent as this could lead to injury.
・Be sure to wear protective goggles, a dust mask, protective footwear, earplugs and other protective equipment when working.
・Keep TORNADO away from gasoline, thinner, petroleum and paraffin.
・Hold the workpiece with clamping devices.
SPECIFICATIONS
Model Code
NK-125
Attachable Blade
125mm/T1.5-2.2 Diamond Blades.
Cut Depth
5-30mm
Weight
520g (Main Unit)
Cutting Material
Concrete, Block, Stone, Tile, ..etc.
Dust Bag capacity
Should be epmtied with every 3m of cutting.
BOSCH:
Proper Grinders
MAKITA:
HITACHI:
PREPARATION
WARNING
・Be sure to turn off the disc grinder and remove the plug from the electrical outlet before attaching TORNADO.
・If you attach TORNADO to a disc grinder but the connector is loose and cannot be securely attached, do NOT use TORNADO.
Using it in this state could lead to injury.
Guard
CONNECTER INSTALLATION
BOSCH
GWS8-115/GWS8-125
GWS6-115
GWS10-125/GWS11-125CI
GWS7-115
GWS14-125CI(E)(T)
GWS9-125
GWS15-125CIH(CIEH)(CITH)
[c] B-Connecter
NK-125
INSTRUCTION MANUAL
GWS6-115/GWS7-115(E)/
GWS8-115/GWS8-125/
GWS9-125/GWS10-125/
GWS11-125CI(E)/GWS14-125CI(E)(T)/
GWS15-125CIH(CIEH)(CITH)
9554NB/9558NB/GA4530/9565CV
G12SS/G12SR3/G13SR3/
G13SB3/G13SE2
SW
MAKITA
[d] M-Connecter
[e] H-Connecter
OVERVIEW
b
a
[a] Main Unit [b] Dust Bag [c] B-Connecter [d] M-Connecter
[e] H-Connecter [f] M4 Screw [g] Cup Washer [h] Spacer (T4.5)
[ i ] Spacer (T7.3) [ j ] Spacer (T9.4) [k] Spacer (T12.6) [m] Base Flange
[n] Foot Plate [p] Flat Screw [q] Wrench [r] Setscrew
Take the Guard off.
Remove the Screws.
Turn the Grinder Body to locate the SW upper position.
Tighten the Screws.
O-Ring
HITACHI
Choose the proper connecter and fit it to [a] Main Unit
with [f] M4 Screw and [g] Cup Washer.
n
j k
i
h
m
c
d
GWS8-115/GWS8-125/GWS10-125/
GWS11-125CI/GWS14-125CI
Remove O-Ring
if it is equipped.
[a] Main Unit
[g] Cup Washer
[f] M4 Screw
N300129
p
e
f g
q
r
-1-
Advertisement
Related Manuals for NAKAYA Tornado NK-125
Summary of Contents for NAKAYA Tornado NK-125
- Page 1 NK-125 INSTRUCTION MANUAL N300129 WARNING ・The supplied connecter may not connect securely to disc grinders. In this case, do not use TORNADO. ・TORNADO is for use when cutting concrete, stone and brick. Do not use when cutting metal or other materials. Do not use with any other type of cutter, such as a grindstone or tipped saw.
- Page 2 FIT TO GRINDER Hold * G13SB3/SE2 need [n] FOOT PLATE. ==>Refer to Page4. Hold the top of the Main Unit and tighten the screws. * Confirm NO tilt in Grinder. * Adjust the angle of Grinder so as to make BOSCH GWS6-115 / GWS7-115 the bottom surface flat.
- Page 3 Knob Bolt Close Surely close the Main Unit and tighten the Knob Bolt. Confirm NO opening at the back side. CUTTING (SELF VACUUM) Surely connect [b] Dust Bag to the duct, then turn the Grinder on and start cutting. Dust Bag should be emptied with every 3m of cutting. Insert deeply [CAUTION] 1.
- Page 4 DEPTH ADJUSTMENT Scale 1. Loosen the Knob Bolt. Base Line 2. Set the Base line with the Scale line of requiring cut depth. 3. Tighten the Knob Bolt. [CAUTION] (1) Surely connect with Cleaner, otherwise the dust can not be collected. Knob Bolt (2) Use the scale just for a reference.