Page 1
MODEL Installation Instructions Round and Oval Type B GasVent Systems for use with natural gas or liquid propane category I and draft hood equipped appliances and appliances listed to use Type B Gas Vent. • Scan Code For French and Spanish Instructions •...
Page 2
Dear Customer, Installer, or End User: IMPORTANT: We welcome any comments regarding Read through all of these instructions matters pertaining to our DuraVent products. before beginning your installation. Failure We welcome any ideas, input or to install this product as described in these complaints and somebody will respond instructions will void the manufacturer’s...
Deletion or modification of any of the required All sizes of Model BV Type B Gas Vent may parts or materials may seriously impair the be used in single and multistory buildings. All...
Large Diameter Model BV Type B Gas Vents for diameters of 10” to 30”. FIG. 2 - Typical Installation of Model BV (3” to 8”) 4. AIR SUPPLY DuraVent Type B Gas Vents are recommended...
Adjustable Tee Cap Length Vent 6. VENT CONNECTOR TYPE AND SIZE R12 Min. Model BV Type B Gas Vent meets all building Insulation Firestop codes and safety standards for use as gas Spacer or appliance vent connectors. Correct selec- Wall Thimble 25mm (1”)
9. WALL SUPPORT/WALL BAND - FIGS 7 & 8 The Wall Support/Band is for use in supporting Firestop 35 ft. of vertical Model BV (3” to 8”) and estab- Spacer/Support lishes the proper 1” clearance to wall to which Plate Firestop placed it is attached, used at maximum 8 ft.
10. USE OF GAS VENT FITTINGS When installed as a Wall Band, slip a vent Do not cut gas vent pipe or fittings. Adjustable section through the band and clamp loosely Lengths are telescoped over fixed lengths, to in place using the bolt and nut provided. Mark accommodate odd distances between vent the locations for the screws which will attach lengths or connectors.
B gas vent section, in order to continue the and sizing guidelines permit a single wall system toward the termination with Model BV connector pipe may be attached to Model BV joint coupling design. Fixed Wye fitting with a Draft Hood Connector...
Page 11
(provided). required for proper venting. The top (outlet) end of the system has now been converted to the DuraVent Model BV Special care must be taken with short gas joint coupling design. vents on duct furnaces, unit heaters, and furnaces in attics to enssure they have sufficient vent height.
12. SUPPORT - PRIMARY AND OFFSETS QUICK GRIP - FIRESTOP/SUPPORT - 3” TO 8” 1. At the desired location, cut a square Gas vent piping must be securely supported. or circular hole in the floor at a minimum Lateral runs are to be supported at least every of 2-1/2 inches larger than the nominal ie 5 feet.
Flashing Flashing over under Roofing Roofing Maintain minimum FIG. 16A - Roof Pitch 7/12 or Less 25mm (1”) clearance to combustible and BV Type B Gas Vent FIG. 15 - Flashing Installation NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
See Table 1 and Fig. 16B 15. MODEL BV DURACAP INSTALLATION Model BV Type B Gas Vent DuraCap and Highwind Cap must be secured using the “DuraLock” feature. To use the DuraLock feature, orient sections as shown in Fig.1 and force the DuraCap to the upper end of the pipe until joint is fully/properly engaged.
Model BV Type B Gas Vent, permitting simple attachment. Adaptation to other Type B Gas NOTE: IN CANADA, ANY PIPE ABOVE THE ROOF Vent may be accomplished by utilizing either LINE MUST BE OF GALVALUME CONSTRUCTION, Model BV Universal Female B-Vent Adapter.
Page 16
B Gas Vent system is not compatible with connector system. the male end of the flexible connector, use a Model BV Universal Female B-Vent Adapter AFTER COMPLETING INSTALLATION or a Universal Female Flexible Connector which are UL Listed and designed to adapt to OF CONNECTOR AND VENT SYSTEM, most manufacturer’s Type B Gas Vent (See...
Page 17
Fig. 21 above the Attic Insulation Shield. TO INSTALL: Select the length of Flexible Connector sufficient to extend from Model BV Type B B-Vent Gas Vent to the appliance to be connected. Insert the outlet (male) end into the inlet end of the gas vent until it fully engages.
Page 18
Two Metal Brackets Installed Assembly Or Firestop If As Shown. Secure Metal Adequately Supported Brackets To Roof Joist. Below Model BV Type B Gas Vent Fig. 25 One 1/4” Sheet Metal Screw To Attach Each Bracket To B-Vent Sheet Metal Plate Attached To Bottom Side Of Roof Joist.
Individual lengths are provided with the the desired length is same type of outlet end connector as achieved. DuraVent Model BV Type B Vent, permit- ting simple attachment. The DuraConnect I Single Wall Expandable Flex Connectors are available in 3” and 4” diameters and can extend from 24”...
Type B Gas Vent (see Figure 28). PIPE SECTION 2 90° ELBOW MODEL BV LARGE DIAMETERS - 10” - 30” NOTE: The following pages are additional information for the installation of the Large LISTED APPLIANCE Diameter Type B Gas Vent Model BV.
10” to 30”. The Vent Pipe Hanger (SBA) is Basic Vent Structure designed for use with 10” and 12” diameters Model BV is available in sizes 10” to 30” and only. They are used to provide lateral and has a 1/2” space between pipe walls. When some vertical support for sections of vent, as calculating the assembled length, allow 1”...
Page 22
The Adjustable Length 36). Section should be positioned directly under the vent pipe section that is being supported. BV GAS VENT JOINT METHOD - Fig. 35 10” TO 30” TO LOCK JOINT 1. Line up seams of both...
Support Assembly Terminate USE OF GAS VENT FITTINGS Vent Vertical Vent At Least 5 Model BV tees, elbows, increasers, and short Feet Adequate lengths are specially designed to facilitate Draft Hood Above Draft Air Supply Connector interconnections.
For diameters 14” to 30”, the termination must 10’ OR LESS terminate as per Figures 38 and 39. A cap or chimney housing offers resistance 2’ MIN 2’ MIN to the entrance of rain, snow and debris, as 2’ MIN well as birds, and will minimize the effect of wind on the vent.
SECTION 3 Type B 2 x 4 Gas Vent - 4” or 5” Oval Four- and five-inch Model BVO Oval Gas MODEL BVO - OVAL GAS VENTS - 4” - 5” - 6” Vent may be installed within a standard 2x4 stud wall if all the following conditions Basic Vent Structure are met.
as shown on Figure 40. 6. After passing through the last Firestop 4. At each floor level above the Tee, install Spacer, the Vent may be finished with either the Firestop Spacer (E) as shown in Figure round or oval fittings, flashings and Cap. (Round pipe, fittings, flashings, and vent caps cost less than corresponding oval parts.) NOTE: Provide at least a 1-inch clearance...
Attic Insulation Shield STEP 4: In some areas, the building code requires the use of an attic insulation shield (AVS) on single-story Type B-W installations. Model BVO Attic Insulation Shield attaches to the top surface of the ceiling plate where oval wall-heater vent enters the attic.
Page 29
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Page 30
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Page 31
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
CSIA Certified Chimney Sweeps, NFI DuraVent products are fully warranted if installed only by a Certified Specialists, or WETT Certified Professionals. professional installer. This Warranty is transferable from the original homeowner to the buyer of the home.