Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DuraVent PelletVent UL 641
Summary of Contents for DuraVent PelletVent UL 641
- Page 1 Installation Instructions Multi-fuel venting system. UL 641, UL 1777...
- Page 2 Read through all of these instructions before We welcome any comments regarding beginning your installation. Failure to install matters pertaining to our DuraVent products. as described in this instruction will void the We welcome any ideas, input or complaints manufacturer’s warranty, and may have an and I’ll make sure that someone responds...
-
Page 3: Table Of Contents
VENTINg SYSTEMS FOR PELLET, OIL AND MULTI-FUEL STOVES For the most up-to-date installation instructions, see www.duravent.com CONTENTS CLEARANCES AND APPLICATIONS ........4 VENT LISTINg, INSTALLATION NOTES . -
Page 4: Clearances And Applications
0” clearance from the masonry efficiency, and convenience,saving both time to nearby combustibles. Never fill any and money. Use only authorized DuraVent required clearance space with insulation PelletVent listed parts. Do not install or any other materials. Combustible damaged parts. -
Page 5: Tools And Equipment You May Need, Permits
to Table 1 for the dimensions of the hole. provided it is inside the fireplace, and the C. Connect Pipe Adapter to stove: Attach fireplace has completely sealed surroundings. 11. Do not connect B-Vent pipe with each section of pipe by pushing male and female ends of pipe together and twisting aluminum liners to pellet appliances. - Page 6 VERTICAL CAP 3 INCH MINIMUM STORM COLLAR FLASHING ATTIC INSULATION SHIELD CEILING SUPPORT FIRESTOP SPACER ATTIC PELLET INSULATION VENT PIPE PIPE ADAPTER SEE TABLE 1 FOR FRAMING STOVE REQUIREMENTS Figure 1 1. The black portion of the Wall Thimble is push together and twist to lock.
- Page 7 desired (Figure 6): APPLY HIGH TEMPERATURE A. Place the appliance according to SEALANT COMPLETELY manufacturer’s instructions. AROUND TOP EDGE OF STORM COLLAR B. Connect the Pipe Adapter to back of stove and attach sufficient pipe to penetrate Wall 12 INCHES MINIMUM Thimble and extend at least 6”...
- Page 8 (c) Not less than 2 ft. (0.61m) from an DuraBlack Chimney Adapter only connects to adjacent building and not less than 7 ft. DuraVent chimney systems. (2.1m) above grade when located adjacent to D. Connect the appropriate size Chimney public walkways.
-
Page 9: Installation Into A Masonry Fireplace
vertically plumb, then slip the Adjustable EXISTING DURATECH, Length up and twist lock it to the Chimney DURAPLUS, OR Adapter. Once all the components are firmly DURACHIMNEY SYSTEM seated and properly aligned, carefully drill three 1/8” diameter holes through the outer sleeve only in the center of the slots located at the bottom of the Adjustable Length pipe. -
Page 10: Installation Through Side Of Masonry Chimney
Bracket to hold the Tee to the rear of the appliance is mandatory. If it is desired to mount the Tee Support to the rear of the stove, obtain approval from the manufacturer TOP VIEW of the stove before drilling, tapping, or performing any other alterations to the appliance. - Page 11 PELLET VENT PELLET VENT NONHARDENING PELLET TALL CONE SEALANT VENT PIPE FLASHING STORM SCREW STORM COLLAR RIGID COLLAR TO OUTER TALL CONE PELLET VENT LINER OF PIPE WITH FLASHING SHEET METAL SCREWS. THIS WILL SUPPORT SYSTEM. MASONRY ANCHORS 6 INCHES MINIMUM FLEX PELLET VENT...
- Page 12 masonry chimney has an offset. If an offset NON-HARDENING exists, then a section of Flex Pipe will be SEALANT TRIM needed to accommodate the offset. BASE TO B. A Tee is installed at the bottom end of the FIT FLUE TILE vertical pipe (Figure 16).
-
Page 13: Installation In A Cathedral Ceiling
INSTALLATION IN A CATHEDRAL CEILINg 1. Mark a line on the side of the Cathedral Ceiling Support Box to correspond to the line of the roof pitch, as shown in Figure 18. Allow for the Support Box to protrude below the low side of the finished ceiling a minimum of 2". -
Page 14: Cleaning And Maintenance
bead of non-hardening sealant around the 12” MINIMUM outside top edges of the Support Box so as to make a seal between the box and the roof. CATHEDRAL Clean out any combustible material or debris CEILING from inside the Support Box. SUPPORT BOX 8. - Page 15 Fire Department. Do not use the appliance or vent until it has been inspected for possible damage. 7. DuraVent is not responsible for flue by- products that might discolor roofs or walls. Fuel: Be sure to follow the recommendations of the appliance manufacturer for the type of fuel to use.
-
Page 16: Warranty
M&G DuraVent, Inc. (“DuraVent”) provides this limited lifetime warranty for all of its products with the exception of Ventinox® (lifetime), and PolyPro® (ten years). Subject to the limitations set forth below, DuraVent warrants that its products will be free from defects in material or manufacturing, if properly installed, maintained and used.