Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for ABI Attachments ABI-BS-GD-339
- Page 1 Owner’s Manual Broadcast Spreader Ground Drive Model: ABI-BS-GD-339 NOTE: This Owner’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all models and the model depicted may di er from yours.
-
Page 2: Table Of Contents
Model and Serial Number Model Number: Serial Number: Version Number: Purchaser’s Name: Contact Information Table of Contents ABI Attachments, Inc General Info & Warranty......3 520 S. Byrkit Ave. Safety............4 Mishawaka, IN 46544 Safety Labels...........7 Uncrating Instructions......8 Customer Support Initial Setup..........9... -
Page 3: General Info & Warranty
TERMS & CONDITIONS “ABI” means ABI Attachments, Inc. 520 S Byrkit Ave, Mishawaka, Indiana 46544, 877.788.7253. The above referenced models are warrantied for 24 months, from the original invoice date, against defects in materials and/or workmanship when put to normal and designed residential, farm, &... -
Page 4: Safety
Safety WARNING! The SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra safety precaution must be taken. When you see this symbol, be alert and carefully read the message that follows it. In addition to design and configuration of equipment, hazard control, and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment. - Page 5 • Lower implement to the ground • Replace parts on this implement and follow all shutdown procedures with genuine ABI Attachments parts before leaving the operator’s seat to OPERATION SAFETY only. perform maintenance. • Do not alter this implement in a •...
- Page 6 USE SEAT BELT AND ROPS • ABI Attachments recommends the AVOID UNDERGROUND UTILITIES use of a CAB or roll-over protective structures (ROPS) and seat Dig Safe, Call 811 (USA Always •...
-
Page 7: Safety Labels
Safety Labels Email: support@abiattachments.com Call Toll Free: 877-788-7253... -
Page 8: Uncrating Instructions
Uncrating Instructions Tools Needed: - Gloves - Safety Glasses - Safety Shoes - Tin Snips / wire cutters - Razor Blade or knife - (2) large adjustable wrenches - (2) 10mm wrenches or socket set - (2) 13mm wrenches or socket set Fig 1. -
Page 9: Initial Setup
Initial Setup M30 nut ABI recommends assembling the broadcast spreader be done by 2 people. Black threaded bushing 1. Locate the hopper, mobile shutter, black threaded bushing and the M30 nut (Fig 1). 2. Slide the black threaded bushing through the bottom hole of the hopper (Fig 2). - Page 10 Initial Setup (cont'd) If this is the case, set the lockwasher o to the side and Spreader disc thread the nut as tight as it will go to draw the square section of the carriage bolt into the wall of the hopper. This will give more thread length at the end of the bolt to remove the nut and reinsert the lockwasher onto the bolt then reinsert the nut and tighten.
- Page 11 14. Slide (1) Ø28 shim onto both le and right axle sha (Fig 27). Slide (1) wheel onto both le and right axle sha s. The side of the wheel with the long tube portion of the hub (with the small hole going thru the side of the hub) faces inward toward the gearbox on the axle (Fig 28 &...
- Page 12 Initial Setup (cont'd) Slide flat plate on flow control assembly into grooves on mobile shutter attached to the bottom of the hopper. Rotate flow control assembly bracket up and behind curved guard. Fig 27. 28mm shim Fig 26. axle sha Fig 20.
- Page 13 Fig 32. Spreader disc Fig 38. Fig 39. Spreader disc Angled brackets w/holes. Fig 33. Fig 34. Mount 1st pivot bracket Pivot bracket should be Fig 40. to main support frame. parallel to spreader disc Remove and replace when properly mounted. bolts, washers and nuts to adjust spreader disc angle.
-
Page 14: Operation Guide
Operation Guide 1. The rotating spreader disc is ground driven by the pneumatic tires which are attached to a drive axle that runs through a sealed gearbox (with tempered high carbon steel gears). 2. Prior to start working, make sure there are no obstructions. -
Page 15: Specifications
Specifications 1. Unless otherwise specified, all hardware is metric. Use only metric tools on metric hardware. Other tools that do not fit properly can slip and cause injury. 2. Right hand and le hand sides of the implement are determined by facing in the direction the implement will travel when going forward. -
Page 16: Parts Description
Parts Description 103-230, 106-230 Broadcast Spreader Assembly Fig 44. Visit: www.abisupport.com... - Page 17 Email: support@abiattachments.com Call Toll Free: 877-788-7253...
-
Page 18: Maintenance
Maintenance 1. Tire MAX inflation - 28 PSI. Replace tire if cracks or missing chunks in tire are present. 2. Before beginning work: A. Apply a thick layer of grease to all exposed moving parts. B. Apply a film of biodegradable oil in crevasses and corners in order to keep corrosive material from rusting areas that are di icult to clean. -
Page 19: Troubleshooting
Troubleshooting WARNING: Be sure tractor engine is o , parking brake is locked, and key is removed before making any adjustments. PROBLEM POSSIBLE CAUSE SOLUTION NON UNIFORM SPREAD OPENING LEVER NOT SET LEVER AT GATE OPENING TO THE PROPER PATTERN POSITIONED CORRECTLY POSITION (SEE "SPREAD ADJUSTMENT"... - Page 20 Contact Information Customer Support ABI Attachments, Inc Email: support@abiattachments.com 520 S. Byrkit Ave. Phone: 877-788-7253 Mishawaka, IN 46544 Website: www.abisupport.com To order parts or to speak to one of ABI’s Customer Service Representatives contact us Monday to Friday 9am to 5pm EST.