Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for jbc Advanced Series
Summary of Contents for jbc Advanced Series
- Page 1 Index Page English H OT- A I R F L OW R E PA I R S TAT I O N TE 5000...
- Page 2 ENGLISH We appreciate the confidence you have placed in JBC in purchasing this station. It is manufactured to the most stringent quality standards in order to give you the best possible service. Before turning on your station, we recommend you to read these instructions carefully.
-
Page 3: Specifications
ENGLISH SPECIFICATIONS OPERATION The station TE 5000 is used for desoldering and Turning on soldering of small and medium sized SMD's by hot- Turn on using the switch on the rear of the air. control unit. The screen shows OFF. - TE 5000 230V 50Hz EU: Ref. - Page 4 ENGLISH RECOMMENDATIONS FOR SOLDERING For soldering AND DESOLDERING Process for small SMD components of two or In hot-air soldering and desoldering processes, three pins such as heating elements, capacitors, melting point is reached as a result of the heat transistors, etc: applied, the function of the air being to bring 1) If the component has been desoldered pre- the required heat to bear on the components.
- Page 5 1) Temperature of about 350°C, air flowrate 1-7. may extend over the circuit on melting and cause short-circuits. 4) Take the component with a JBC PK 6060 or DP 6070 Pick & Place or otherwise with fine pincers, place it in position on the circuit and hold it in place.
- Page 6 ENGLISH 4) Use the heater like the previous case, - Use the VACUUM button to start the suction advancing slowly from one extreme to another pump and then fit the tripod. Press the sucker of the pins line. down until it sticks onto the component. (*) Alloy 62 Sn/ 36 Pb/ 2 Ag Type RMA/CMA.
- Page 7 ENGLISH B) Extractor: - When the soldering flux turns liquid the extractor will automatically lift the component. - Select extractor size in function of the IC to be desoldered. Use the VACUUM button to start the suction pump. There are different models of protectors and extractors as accessories.
-
Page 8: Operating Incidents
The following messages are displayed: - BLANK SCREEN Power failure. Check for blown fuses. - ERR 1 The temperature will not rise. Possible causes: heating element open or blown JBC reserves the right to make technical changes without fuse. prior notification. - Page 9 ITALIANO AD 2200 AR 5500 Soldering stations for specialized use with SMD Desoldering station which enable the rapid components assemblies. desoldering of all kinds of insertion components. AM 6000 JT 7000 Hot-air flow repair station for desoldering all types Station for rework and repair of through-hole and SMT boards.
- Page 10 ITALIANO ELECTRIC WIRING DIAGRAM TE 5000 230V 50Hz...
-
Page 11: Electric Wiring Diagram
ITALIANO ELECTRIC WIRING DIAGRAM TE 5000 120V 60Hz... - Page 12 ITALIANO TE 5000 230V 50Hz...
- Page 13 ITALIANO TE 5000 120V 60Hz...
- Page 14 ITALIANO PROTECTOR EXTRACTOR Fig. 2 Fig. 1 A/mm B/mm A/mm B/mm PART Nº PART Nº 00 / 0934035 13.0 52 / 0932052 20.0 20.0 00 / 0934040 19.0 64 / 0932064 20.0 26.0 0934080 21.0 80 / 0932184 24.0 24.0 32 / 0932220 10.0 10.0...
-
Page 15: Warranty
GARANTIE FRANÇAIS JBC garantit cet appareil 2 ans contre tout défaut de fabrication. Cela comprend la réparation, le remplacement des pièces défectueuses et la main d'oeuvre nécessaire. Sont exclues de cette garantie les pannes provoquées par une mauvaise utilisation...
Need help?
Do you have a question about the Advanced Series and is the answer not in the manual?
Questions and answers