Table of Contents
Advertisement
Quick Links
WorkForce®2
Model WF2
User's Information
WorkForce® model WF2 is a worker-worn motion-
sensing Man-Down Alarm that uses proprietary, ISM
license free, high performance RF (radio-frequency)
wireless signaling to help protect workers in dangerous
and hazardous environments.
WorkForce® provides real-time motion-sensing, includ-
ing fall-detection, and contains an Emergency Alarm
Button to immediately transmit a distress alarm signal.
WorkForce® Alarm Monitoring (AM) version also
receives distress alarm signals from other workers
equipped with WorkForce® and alerts the user with
audible and visual indicators. Other emergency
signaling features of WorkForce® include Evacuate, PAR,
Roll-Call and optional Out-of-Range indication.
A complete worker safety system can be achieved
by using additional Grace monitoring products with
locating capabilities.
Emergency
Alarm Button
Antenna
Top LED Indicators (4)
Satellite LED Icon
Indicates GPS Model
Menu Button
Select Button
Bright
Menu
OLED Screen
Hotkeys
Ü—˜#
System Status
Piezo
Indicators
Sounder
(4 Side LEDs)
Rear View with
Rear View with
optional Grip Clip
Swivel Clip
for attachment
for attachment
Micro B USB Connection
for Configuration
and Battery Charging
Grace Industries, Inc.
WorkForce WF2 UI 2022-02
Advertisement
Table of Contents
Related Manuals for Grace Industries WorkForce 2
Summary of Contents for Grace Industries WorkForce 2
- Page 1 Ü—˜# System Status Piezo Indicators Sounder (4 Side LEDs) Rear View with Rear View with optional Grip Clip Swivel Clip for attachment for attachment Micro B USB Connection for Configuration and Battery Charging Grace Industries, Inc. WorkForce WF2 UI 2022-02...
- Page 2 Settings option in WorkForce Configuration tool to enable/dis- for the purpose of indicating to the user they may be out of the able this feature. effective signaling range of the system. When this feature is enabled and under normal operation, the user Grace Industries, Inc.
-
Page 3: Mode Selection
SATELLITE-GPS (available on GPS models) tri-tone will be produced and “System Test Timeout” message • Slow blinking Green LED when GPS signal is acquired. displayed. • Slow blinking Red/Green LED when NO GPS signal is detected. Grace Industries, Inc. -
Page 4: Battery Power Level
• Partially charged: While charging, these LEDs will cycle from #4 up to the current Battery Power Level. WorkForce®1 shown with Micro B USB Cord and 120VAC Charger Adapter (p/n: 120-G-WF950) Optional 12VDC Charger Adapter shown at left Grace Industries, Inc. -
Page 5: System Faults
Pressing MENU will navigate away from the Send Message page. To enter Setup Mode, proceed to the Setup Mode page by Resetting the device will return the WorkForce® to the home page. Grace Industries, Inc. - Page 6 The Enable GPS page allows the user to enable or disable the The Radio Range Test mode of the WorkForce® is used to test GPS function of the WorkForce®. radio signal propagation during on-site testing and system Navigate to this page by pressing the MENU button. installation. Grace Industries, Inc.
-
Page 7: Battery Level
Nov 24 2021 12:44:26 Page 4 - Radio Firmware Version Radio Version: V3.4-7691 Note: WorkForce® will remain on selected page until Select button is pressed or the unit is reset. Resetting the device will return WorkForce® to the home page. Grace Industries, Inc. -
Page 8: Specifications
WARNING: Any motion sensing Alarm Time period longer than 90 seconds is potentially dangerous to the user of this product. The longer the motion sensing time period is, the greater the risk of exposing the user to a delayed response to an incapacitated, distressed worker. Grace Industries, Inc. -
Page 9: Definition Of Terms
Alarm Inhibit Timer: When WorkForce® receives an alarm message usually from a centralized base location. from another GRACE Industries device and that alarm is cleared, Motion Sensing Activation Icon: Appears on the Icon Line of the the Alarm Inhibit Timer provides a 30 second period of time where Home Page when the Motion Sensing feature is active. - Page 10 SELECT button. To exit Survey mode, press and release both side buttons (MENU and SELECT) and then again press and hold the MENU and SELECT buttons simultaneously to power off the unit. c. The WorkForce® model WF1 is placed in Survey mode after Grace Industries, Inc.
- Page 11 Try connecting with a different USB port on the computer. The best port is a directly connected port on the body of the PC. USB hubs are a common point of communications trouble. Turn computer completely off for 5 minutes and try again. Grace Industries, Inc.
- Page 12 3) Return products including Return Authorization number, prepaid and accompanied by original proof of purchase that states the date and location of purchase to: Grace Industries, Inc., Repair Department, 305 Bend Hill Road, Fredonia, PA 16124, USA.
Need help?
Do you have a question about the WorkForce 2 and is the answer not in the manual?
Questions and answers