Related Manuals for Scantool MBR
Summary of Contents for Scantool MBR
- Page 1 Industrivej 3-9 DK-9460 Brovst Tlf.: +45 98 23 60 88 Fax: +45 98 23 61 44 SCANTOOL Manual Bending Roller MBR – Models...
- Page 2 Ph.: +45 98 23 60 88 Fax: +45 98 23 61 44 Hereby declares that SCANTOOL Manual Bending Roller MBR – Models are manufactured in accordance with the provisions of the European Parliament and Council Directive 2006/42 / EC of 17 May...
-
Page 3: Table Of Contents
Table of Contents 1 SAFETY SAFETY NOTES SUITABLE WORKING DIRECTIONS WORKING AREA EQUIPMENT DANGER NOISE DANGER ZONES ORKING PERSONNEL PERSONNEL P ROTECTION 1.10 ON SETUP (LOOK FOUNOATION PIAN) ROTECTION 1.11 IMRORTANT POINTS 2 PROTECT (COVER) ARRANGMENT PLEASE CONTROL THIS PROTECT ARRANGEMENT: 3. -
Page 4: Safety
8 WARRANTY 8.1 G UARANTEE 1 SAFETY SAFETY NOTES The THREE ROLL BENDING MACHINE is supplied with necessary guards to protect from injuries by Worm-type Gearbox and other gears. The only other area which needs to be carefully monitored during use is the rotational area of the roll. Also abuses and misuses should cause following problems: •... -
Page 5: Suitable Working Directions
SUITABLE WORKING DIRECTIONS Primary Operations of the machine: Sheet Plate Bending and Sheet Plate Conical Bending. Conical Bending is not suitable for serial manufacturing. WORKING AREA Before setting up the machine check the dimensions on the diagram below. EQUIPMENT DANGER When load or unloading the machine, if you use another carrying connection, the protection arrangement and user equipment can be used position. -
Page 6: Noise
NOISE The Noise level for this machine is strictly under 70 db. DANGER ZONES The roiling area of the machine is the most dangerous area as it' cannot be guarded. Only the user himself is responsible for his safety. Even the danger here is not very significant and avoidable following points must be done in case of any emergency. -
Page 7: Imrortant Points
1.11 IMRORTANT POINTS The machine must be used by qualified and technical personnel at all times. All modification and changes on the machine without written confirmation of the manufacturer is forbidden and if such a case occurs, the responsibilities of the manufacturer will be out of consideration. -
Page 8: Protect (Cover) Arrangment
2 PROTECT (COVER) ARRANGMENT The protection arrangement of THE MACHINE is showing in the following pages. Here is the check list for protect arrangement. PLEASE CONTROL THIS PROTECT ARRANGEMENT: • Before working every time • 1 time a week • After every repair Control this list too: •... -
Page 9: Setting Up
3. SETTING UP 3.1 CARRYING AND HAULING The following sketch must be used while the machine is transported with a crane. Any damages occurring during transportation will not be covered by our warranty. -
Page 10: Opening The Package
OPENING THE PACKAGE If any visible damage exists on the machine when you receive the machine immediately inform the dealer or manufacturer. Also never forget to state the visible damage on transport documents. The packing material is completely safe and do not consist any environmentally dangerous articles. -
Page 11: Environment Conoitions
ENVIRONMENT CONOITIONS. While setting up the machine dimensions that should be taken as reference are given in the machines working area. To get a higher working performance and to lengthen the life time of the machine and for the security of the environment and the replacement place take care to these: •... -
Page 12: Machine Dimensions
4. MACHINE DIMENSIONS Machine Dimensions. LENGHT HEIGHT... -
Page 14: Before Operating
4.2 BEFORE OPERATING Before operating be sure that this manual is thoroughly read and understood by the personnel who is to directly operate the machine. 4.3 Lubrication As all mechanical machines this machine is also need to be Iubricated periodically check the Lubrication Plan for reference to lubrication points. -
Page 15: Operation
5. OPERATION Up to this point if there is anything you do not understand or do not proceed to the next pages ask to us or your dealer about any point you did not understand. It is a responsibility to use this machine as it directly affects your health and safety if you misuse or abuse the machine aware or not. - Page 16 • Last bending. • Change the sheet, and do the same things at pre-bending.
- Page 17 • Bending and Cylinder bending Start to roll the sheet and bend it since it comes as a cylinder figure as shown at the picture.
-
Page 19: Lubrication Plan
6 LUBRICATION PLAN... -
Page 20: Drawing For Bending Roller Mbr
6.1 Drawing for Bending roller MBR... -
Page 21: Spare Parts List For Bending Roller Mbr
6.2 Spare parts List for Bending roller MBR 1. FRAME LEG 2. SUPPORT BAR 3. MAIN FRAME 4. MAIN FRAME 5. TOP ROLL 6. IDLE ROLL 7. BOTTOM ROLL 8. TOP ROLL BUSHING 9. IDLE ROLL BUSHING 10. BOTTOM ROLL BUSHING 11. -
Page 22: Opening Top Roll
7. OPENING TOP ROLL... - Page 23 8 Warranty 8.1 Guarantee If within 2 year of purchase this machine supplied by Scantool A/S becomes defective due to faulty materials or workmanship we guarantee to repair or replace the machine or defective part or parts free of charge provided that: The product is returned complete to one of our Service Branches or Official Service Agents.
Need help?
Do you have a question about the MBR and is the answer not in the manual?
Questions and answers