Table of Contents
Advertisement
CARE & MAINTENANCE – CONT�
CLEANING
Hand-Washing
Wash containers, lids, and blade
assemblies in warm, soapy water.
Use a dishwashing utensil with
a handle to avoid direct contact
with the blades. Use the included
cleaning brush to remove excess
residue, such as when dealing with
stuck-on ingredients, like doughs
and batters. Exercise care when
handling the blade assembly as
the blades are sharp. Thoroughly rinse and
air-dry all parts.
NOTE: The built-in tamper in the Power
Smoothie Bowl is not removable.
Dishwasher
Containers, lids, and blade assemblies are
dishwasher safe. Ensure the blade assembly
and lid are removed from the container
before placing in the dishwasher.
NOTE: For best results, use a dishwasher
to remove stuck-on ingredients.
Motor Base
Unplug the motor base before cleaning.
Wipe motor base with a clean, damp cloth.
DO NOT use abrasive cloths, pads, or
brushes to clean the base.
22
AU 02 8801 7666 | NZ 0800 112 660
STORING
For cord storage, wrap cord with hook-and-
loop fastener near the back of the motor
base. DO NOT wrap the cord around the
bottom of the base for storage.
DO NOT store blended or unblended
ingredients in the cup or smoothie bowl
with the blade assembly attached.
DO NOT stack items on top of the
containers. Store any remaining attachments
alongside the unit or in a cabinet where they
will not be damaged or create a hazard.
Store the grinder attachment with the lid
attached to the grinding cup/blade assembly.
RESETTING THE MOTOR
This unit features a unique safety system
that prevents damage to the motor and
drive system should you inadvertently
overload it. If the unit is overloaded, the
motor will be temporarily disabled. Should
this occur, follow the reset procedure below.
1 Unplug the unit from the electrical outlet.
2 Allow the unit to cool for approximately
15 minutes.
3 Remove the container's lid and blade
assembly. Empty the container and
ensure no ingredients are jamming the
blade assembly.
IMPORTANT: Ensure that maximum
capacities are not exceeded. This is the most
typical cause of appliance overload.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments,
visit AU ninjakitchen.com.au or
NZ ninjakitchen.co.nz
TROUBLESHOOTING GUIDE
WARNING: To reduce the risk of shock and unintended operation,
turn power off and unplug unit before troubleshooting�
Display reads "- -"�
•
If the display reads "- -", install a container and the available program buttons will
illuminate, indicating the unit is ready for use. Ensure the lid is fully engaged and the
container has been rotated clockwise and clicked to lock into place.
•
If vessel is properly installed and the display reads '- -', ensure the interior of the base
area is clean of any debris.
•
If the display reads "- -", the Coffee & Spice Grinder is either not installed or not properly
installed on the motor base. Ensure it is properly installed by rotating clockwise until it
clicks into place. The program buttons will illuminate, indicating the unit is ready for use.
Display reads "E1"�
•
If the display reads "E1", unplug the unit from the electrical outlet and allow it to cool for
15 minutes. Remove the blade assembly or the Coffee & Spice Grinder and empty the
contents to ensure no ingredients are jamming the blade assembly.
Display reads "E2"�
•
If the display reads "E2" unplug the unit from the electrical outlet and allow it to cool for
5 minutes. Remove the blade assembly and empty the contents to ensure no ingredients
are jamming the blade assembly. If output is too thick and ingredients are not processing
properly, add more liquid.
Blade speed sometimes changes when blending thinner ingredients�
•
When using speed 9 or 10 with the Pitcher, you may notice a change in the blade speed
when blending thinner ingredients. This is due to the smart technology in the blender
and is part of the unit's normal operation.
Unit doesn't mix well; ingredients get stuck�
•
Using the Auto-iQ programs is the easiest way to achieve great results. The pulses and
pauses allow the ingredients to settle toward the blade assembly. If ingredients are
routinely getting stuck, adding some liquid will usually help.
•
When filling the cup, start with fresh fruit or veggies, then leafy greens or herbs. Next add
liquids or yoghurt, then seeds, powders, or nut butters. Finally, add ice or frozen ingredients.
•
If using the Power Smoothie Bowl, during the blending process twist the built-in tamper
counterclockwise continuously to circulate ingredients.
Unit moves on counter while blending�
•
Make sure the surface and feet of the unit are clean and dry.
Preset program will not work�
•
The unit can detect which container is on the motor base. You may be trying to use a program
that is not designed for the container you have installed. The programs will light up, indicating
which programs are available for each container.
Food is not evenly chopped�
•
For best results when chopping, cut pieces of ingredients in a uniform size and don't overfill
the Pitcher. Refer to the Quick Start Guide or Inspiration Guide for food prep instructions.
AU ninjakitchen.com.au | NZ ninjakitchen.co.nz
23
Advertisement
Table of Contents
