Temperature controlled soldering station (3 pages)
Summary of Contents for Xytronic LF- 8800
Page 1
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 Instruction Manual L F- 8800 Temperature Controlled Soldering/Desoldering Station For Lead-free soldering application and rework on professional SMD electronics.
NIP: 521-044-00-73 INTRODUCTION Thank you for purchasing Xytronic’s high power soldering/desoldering station – the best solution for all your soldering/desoldering equipment needs especially for the lead free applications! We believe you will be more than satisfied with the many features and the versatility of your new soldering/desoldering station.
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 delayed switch feature has been incorporated for the unit that allows the pump to continue sucking for 1.5 seconds after the actuator switch is released. ■...
Page 4
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 working surface of the tip as possible. This results in both a rapid heat up, fast recovery and exacting temperature control with minimal overshoot. The revolutionary “Zero Voltage”...
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 SPECIFICATIONS: Model LF-8800 Input 120Vac 60Hz 230Vac 50 Hz Fuse T3.15A Soldering 32Vac/100W Output Desoldering 32Vac/100W Soldering 150-480℃ Temperature Range Desoldering 300℃-450℃...
Page 6
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 the unit will be under the status of no password. If the user sets “100” then means the unit will be under the password status. Press “SET” key once to finish password setting and the unit will backup mode, the user can continue set other modes or back from the setting mode.
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 6. Wake-up method ① Temperature Down Suspend: If the unit is set at Sleep mode function, after 20min idleness, the system will enter the sleep mode automatically, the temperature of ℉) soldering will go down to 150℃...
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 IMPORTANT: The temperature above 410℃ (770℉) is not recommended for normal soldering functions, but can be used for short periods of time when high temperatures are required.
Page 9
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 be flashed on and off to maintain the set temperature. The unit now is ready for use. 8. When you only use soldering iron or desoldering iron, you can set the power off suspend mode by pressing keys “...
Page 10
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 4. Wiping the tip on a high sulfur content, dirty or dry sponge. 5. Contact with organic substances such as plastic, resin, silicone, grease and other chemicals.
Page 11
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 due to the tip, solder collector, tube or in-line filter. CAUTION: THE DESOLDER SWITCH MUST BE “OFF” AND ALLOW THE IRON TO COLL BEFORE ATTEMPTING THE FOLLOWING PROCEDURES: 1.
Page 12
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 FIG-4 FIG-5 10. Remove the tip by using a pliers as in Figures 6 & 7. FIG-6 FIG-7 11. Insert the stainless tube of the tip back in the barrel to melt the solder in around 5 seconds as in Figure 8.
Page 13
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 2. Slide out the solder collector as in Figure 11. (CAUTION: The solder collector is glass and thus retains heat, handle with care!) FIG-11 3.
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 FIG-15 FIG-16 5. Remove old cotton filter and replace (see Figures 17 & 18). FIG-17 FIG-18 IN LINE FILTERS 1.
Page 15
Dane kontaktowe: NDN - Zbigniew Daniluk tel.: (22) 641-15-47 ul. Janowskiego 15 e-mail: ndn@ndn.com.pl Dystrybucja i serwis 02-784 Warszawa NIP: 521-044-00-73 Soldering tips for 307A MAINTENANCE NOTE FOR DIA100 Change of Cotton Filament (76-1411030): Please note that the cotton filament cannot be washed with the water. Water drops would be sucked into the Pump and may cause the pump damaged within 1 to 2 months.
Need help?
Do you have a question about the LF- 8800 and is the answer not in the manual?
Questions and answers