Tuner Mode; Antenna; Cable; Satellite - Nokia Smart TV 2400A Manual

24”, 32”, 39”, 43”, 50”, 55”, 58”, 65”, 75”, 43”, 50”, 55”, 58”, 65”, 70”
Table of Contents

Advertisement

7. Tuner mode

Note: If you don't want to perform a tuner scan, select one of the available options anyway. You can skip the
scan at some later stage of the installation wizard. If you skip this step you can perform a channel search later
using the related Channels menu options.
The next step is the selection of the tuner mode. Select your tuner preference to install channels for Live
TV function. Antenna, Cable and Satellite options are available. Highlight the option that corresponds to your
environment and press OK or Right directional button to proceed.

7.1. Antenna

If Antenna option is selected, the TV will search for digital terrestrial and analogue broadcasts. On the next
screen highlight Scan option and press OK to start the search or select Skip Scan to continue without performing
a search.

7.2. Cable

If Cable option is selected, the TV will search for digital cable and analogue broadcasts. If any, available operator
options will be listed on the Select Operator screen. Otherwise, this step will be skipped. You can select only one
operator from the list. Highlight the desired operator and press OK or the Right directional button to proceed.
On the next screen select Scan option to start a search or select Skip Scan to continue without performing a
search. If Scan is selected a configuration screen will be displayed next. Scan Mode, Frequency (kHz), Modulation,
Symbol Rate (kSym/s), Network ID options may need to be set. To perform a full scan set the Scan Mode as Full/
Advance if available. Depending on the selected operator and/or Scan Mode some options may not be available
to be set.
Once you are done with setting available options, press the Right directional button to proceed. The TV will start
to search available broadcasts.

7.3. Satellite

If Satellite option is selected, Satellite Type screen will be displayed next. Preferred Satellite and General Satellite
options will be available. Select one and press OK to proceed.
Note: Preferred Satellite and General Satellite options may not be available depending on the selected country.
In this case the DVBS Configuration Setting screen will be displayed after selecting the tuner mode as Satellite.
If Preferred Satellite option is selected, next screen will be Select Operator screen. You can select only one
operator from the list. Highlight the desired operator and press OK or the Right directional button to proceed.
Some of the following options may be preset depending on the selected operator in this step. Check the
parameters before proceeding and adjust if necessary.
7.4. DVB–S configuration
DVB-S Configuration Setting screen will be displayed next. First Antenna type should be set (This option may be
named as Satellite type depending on the country selection.) Universal, Single Cable and Jess Single cable options
are available. Set the Antenna Type as Universal for Direct and DiSEqC satellite systems. If you set the antenna
type as Universal, press the Right directional button to proceed to the next step. If the antenna type is set as
Single Cable or Jess Single cable, there will be three more additional options on the DVB-S Configuration Setting
screen: Tuner, Band frequency and User Defined. User Defined option will be available if the Band frequency is set
as User Defined. Set these options if available and press the Right directional button to proceed.
Depending on the country and satellite type selections you made in the earlier steps of the initial setup process,
Load Preset List screen may be displayed next. Highlight Load Preset List and press OK or the Right directional
button to proceed with the SatcoDX installation. You can also skip this step by selecting Skip option.
After the parameters on the DVB-S Configuration Setting screen are configured according to your environment
and pre-set list installation preference is selected the next step may be Select Satellite screen. You may be
able to set up different satellites depending on the selected antenna type and operator in the previous steps.
Highlight the desired satellite option and press OK to set the parameters (If you have a Direct satellite system,
DiSEqC Set option should be set as DiSEqC A.). The Satellite Status of the first satellite option will be set as On.
18

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents