Page 1
All manuals and user guides at all-guides.com ® PATENT PENDING Model No. WESY97300 Serial No. (Write the serial number in the space above for reference.) Serial Number Decal QUESTIONS? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have...
Remove the EXPLODED DRAWING/PART LIST and the PART IDENTIFICATION CHART before beginning assembly. WEIDER is a registered trademark of ICON Health & Fitness, Inc. LIMITED WARRANTY ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of ninety (90) days from the date of pur- chase.
All manuals and user guides at all-guides.com IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the home gym system. 1. It is the responsibility of the owner to ensure 13. Always disconnect the lat bar from the home that all users of the home gym system are gym system when performing an exercise adequately informed of all precautions.
Whether your goal is a shapely figure, dramatic number before calling. The model number is muscle size and strength, or a healthier cardiovascular WESY97300. The serial number can be found on a system, the PRO 9730 will help you to achieve the decal attached to the WEIDER ®...
All manuals and user guides at all-guides.com ASSEMBLY Before beginning assembly, carefully read the • As you assemble the home gym system, be sure following information and instructions: that all parts are oriented as shown in the drawings. • Place all parts of the home gym system in a cleared area and remove the packing materials;...
Page 6
All manuals and user guides at all-guides.com 3. Press a 2” Square Inner Cap (27) into the Rear Upright (56). High Side of Bracket Attach a Rubber Bumper (90) to the Rear Upright (56) with a #8 x 1/2” Tap Screw (89). Slide the Rear Upright (56) onto the 5/16”...
Page 7
All manuals and user guides at all-guides.com 5. Set two Weight Bumpers (19) onto one of the Drilled holes brackets on the Stabilizer (5). Insert two must be at Weight Guides (62) through the Weight the top Bumpers and the bracket on the Stabilizer. Be sure that the drilled holes in the Weight Guides are at the top, as shown.
Page 8
All manuals and user guides at all-guides.com 7. Press a 2” Square Inner Cap (27) into each end of the Top Frame (55). Press a 1 3/4” Square Inner Cap (44) into each end of the crossbar on the Top Frame. Press two 1” Round Inner Caps (49) into the top of the crossbar.
Page 9
All manuals and user guides at all-guides.com 10. Press a 1 3/4” Square Inner Cap (44) into the top of a Press Arm (46). Press a 1” Round Inner Cap (49) into the side of the Press Arm. Attach the Press Arm to one side of the Press Frame (17) with two 5/16”...
Page 10
All manuals and user guides at all-guides.com 13. Press two 1” x 2” Inner Caps (83) into the indicated end of the Squat Arm (79). Lubricate a 3/8” x 3 1/4” Bolt (85). Attach the Squat Arm (79) to the Front Upright (42) with the Bolt and a 3/8”...
Page 11
All manuals and user guides at all-guides.com 16. Wrap the High Cable (23) around a “V”-Pulley (6). Attach the “V”-Pulley and a Long Cable Trap (50) to the indicated bracket on the Front Upright (42) with a 3/8” x 2 1/2” Bolt (7) and a 3/8”...
Page 12
All manuals and user guides at all-guides.com 20. Route the High Cable (23) around one of the 3 1/2” Pulleys (15) attached to the “I” Plates (81). Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly.
Page 13
All manuals and user guides at all-guides.com 23. Attach the High Cable (23) to a Small “U”- Bracket (67) with a 1/4” Nylon Locknut (2) and a 1/4” Washer (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing.
Page 14
All manuals and user guides at all-guides.com 26. Attach the 3 1/2” Low Pulley (88) and the 5/8” x 9/16” Spacer (73) to the indicated hole in the Press Frame (17) with a 3/8” x 3 3/4” Bolt (71), and a 3/8” Washer (9). Be sure that the 3/8”...
Page 15
All manuals and user guides at all-guides.com 29. Wrap the Low Cable (86) around a 3 1/2” Pulley (15). Attach the Pulley and a Cable Trap (66) to the Press Frame (17) with a 3/8” x 3 1/2” Bolt (16), a 3/8” Washer (9) and a 3/8”...
Page 16
All manuals and user guides at all-guides.com 33. Route the Low Cable (86) over the lower 3.1/2” Pulley (15) attached to the “I”-Plates (81). The Cable must be routed from the direction shown. 34. Slide a 5/16” Washer (8) onto a 5/16” x 3” Bolt (93).
Page 17
All manuals and user guides at all-guides.com 37. Wrap the Rear Cable (95) around a 3 1/2” Pulley (15). Attach the Pulley to the bracket on the Stabilizer (5) with a 3/8” x 1 3/4” Bolt 95 15 (87) and a 3/8” Nylon Locknut (21). 38.
Page 18
All manuals and user guides at all-guides.com 40. Attach the Small Backrest (80) to the Rear Upright (56) with two 1/4” x 2 1/2” Screws (43) and two 1/4” Washers (10). 41. Press a 1 3/4” Square Inner Cap (44) into the Rear Seat Frame (77).
Page 19
All manuals and user guides at all-guides.com 43. Attach the Large Backrest (41) to the Front Upright (42) with two 1/4” x 2 1/2” Screws (43) and two 1/4” Washers (10). The Backrest must be oriented as shown. Thick End 44.
Page 20
All manuals and user guides at all-guides.com 45. Press a 1 1/2” Square Inner Cap (32) into the Leg Lever (29). Lubricate the 5/16” x 2 1/4” Bolt (33). Attach the Leg Lever (29) to the Seat Frame (36) with the Bolt and a 5/16” Nylon Locknut (3). Do not overtighten the Nylon Locknut.
Page 21
All manuals and user guides at all-guides.com 48. Remove the backing from the PRO 9730 decal and apply it to the home gym system as shown. PRO 9730 49. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT, beginning on page 22 of this manual.
All manuals and user guides at all-guides.com ADJUSTMENT The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the cor- rect starting position for the exercise to be performed.
Page 23
All manuals and user guides at all-guides.com ATTACHING THE LEG LEVER TO THE LOW PULLEY STATION To use the Leg Lever (29), the seat must be attached to the front upright (see ATTACHING AND REMOV- ING THE SEATS below). Attach one end of the Chain (52) to the Low Cable (86) with a Cable Clip (53).
Page 24
All manuals and user guides at all-guides.com WEIGHT RESISTANCE CHART This chart shows the approximate weight resistance at each station. “Top” refers to the 6.5 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. Weight resistance shown for the butterfly arm station is for each butterfly arm.
All manuals and user guides at all-guides.com TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the home 23, 95...
The starting and ending points of each Cable have been labeled. The numbers show the proper route for each Cable. IMPORTANT: If the Cables have not been correctly routed, the WEIDER PRO 9730 will not function properly and damage may occur.
Page 27
All manuals and user guides at all-guides.com High Cable (23) Press Cable (58) High Pulley Rear Upright Weight Stack Long “U” Bracket...
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre- pared to give the following information: 1. The MODEL NUMBER of the product (WESY97300). 2. The NAME of the product (WEIDER ®...
Page 29
Please Note: The assembly is divided into four stages: 1) frame assembly, 2) press, squat, and butterfly arm assembly, 3) cable and pulley assembly, and 4) seat and backrest assembly. The hardware for each stage is packaged separately. Wait until you begin each assembly stage to open that parts bag. WESY97300 R1097A...
Page 30
All manuals and user guides at all-guides.com 1/4" Nylon Locknut (2)–5 1/4" x 2 1/4" Carriage Bolt (38)–1 5/16" Nylon Jam Nut (84)–2 5/16" Nylon Locknut (3)–24 1/4" x 2 1/2" Screw (43)–5 3/8" Nylon Locknut (21)–22 1/4" x 2 1/2" Carriage Bolt (91)–1 1/4"...
Page 31
All manuals and user guides at all-guides.com 3/8" x 3/4" Bolt (24)–4 1 1/8" x 2 1/2" Plastic Bushing (74)–2 5/16" x 1 3/4" Bolt (72)–2 3/8" x 1 3/4" Bolt (87)–4 5/8" x 9/16" Spacer (73)–1 1/2" x 17/32" Spacer (94)–2 3/8"...
Page 32
All manuals and user guides at all-guides.com 3/4" Round Inner Cap (34)–4 1" Round Inner Cap (49)–6 1" Round Cover Cap (70)–6 5/16" x 2" Eyebolt (35)—1 1" Square Inner Cap (65)—1 2" Square Cover Cap (78)–2 1 3/4" Square Inner Cap (44)–7 1 1/2"...
Page 33
All manuals and user guides at all-guides.com REMOVE THIS PART LIST/EXPLODED DRAWING FROM THE MANUAL...
Page 34
All manuals and user guides at all-guides.com PART LIST—Model No. WESY97300 R1097A Key No. Qty. Description Key No. Qty. Description 5/16” x 2 1/2” Carriage Bolt Long Cable Trap 1/4” Nylon Locknut Rear Base 5/16” Nylon Locknut Chain Front Base...
Page 35
All manuals and user guides at all-guides.com EXPLODED DRAWING—Model No. WESY97300 R1097A...
Need help?
Do you have a question about the WESY97300 and is the answer not in the manual?
Questions and answers