Chipset & chipset based m/b for socket am2+ 64-bit quad core processor (14 pages)
Summary of Contents for AMD 790GX Series
Page 1
USER'S MANUAL AMD 790GX & AMD SB750 Based M/B For Socket AM3 Series Quad Core Processor NO. G03-MA3890X2-F : Release date: July, 2010 Trademark: * Specifications and information contained in this documentation are furnished for information use only, and are...
Page 2
Environmental Safety Instruction Avoid the dusty, humidity and temperature extremes. Do not place the product in any area where it may become wet. 0 to 40 centigrade is the suitable temperature. (The figure comes from the request of the main chipset) ...
CODEC is fully compatible with Sound Blaster Pro standards that offer you with the home cinema quality and satisfying software compatibility. AMD 790GX series motherboards offer one PCI-Express 2.0 x16 by 16 deliver up to 8Gbyte/sec data transfer rate at each relative direction. The AMD 790GX motherboards also carry two 32-bit PCI slots guarantee the rich connectivity for the I/O peripheral devices.
1-1.1 Special Features of Motherboard CPU Thermal Throttling Technology (The CPU Overheat Protection Technology) To prevent the increasing heat from damage of CPU or accidental shutdown while at high workload, the CPU Thermal Throttling Technology will force CPU to enter partially idle mode from 87.5% to 12.5% according to preset CPU operating temperature in BIOS (from 40℃...
1-2 Specification Spec Description Design Micro ATX form factor; 4 layers PCB ;size:24.5cm*21.0cm AMD 790GX North Bridge Chipset Chipset AMD SB750 South Bridge Chipset Support AM2 CPU under 65W and AM2+ CPU under 95W Support AM3 the following CPU under 95W: Phenom II x 6;...
2-1 CPU Installation This motherboard provides a socket surface mount, Zero Insertion Force (ZIF) CPU AM2 socket, referred to as the mPGA940 socket that supports AMD AM3/MA2+/AM2 CPU. The CPU that comes with the motherboard should have a cooling FAN attached to prevent overheating.
2-3 Expansion Slots One PCI-Express2.0 x16@16 lane graphic slot offer 8Gbyte/sec data transfer rate at each relative direction and up to 16Gbyte/sec concurrent bandwidth at full speed. Fully compliant to the PCI Express Base Specification revision2.0, support PCI Express VGA card, and other PCI Express device. Two 32-bit PCI slots guarantee the rich connectivity for the I/O of peripherals.
Chapter 3 Connectors, Headers & Jumper Setting 3-1 Connectors Power Connector (24-pin block): ATXPWR1 ATX Power Supply connector: This is a new defined 24-pins ROW1 ROW2 connector that usually comes ROW1 ROW2 ROW1 ROW2 3.3V 3.3V with ATX case. The ATX Power 3.3V -12V Supply allows using soft power...
Page 12
(2) ATX 12V Power Connector (8-pin block): ATX12V1 This is a new defined 8-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully supports Socket AM2+/AM3 processor must including this connector for support extra 12V voltage to maintain system power consumption.
Page 13
(7) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly.
3-2 Headers (1) Line-Out/MIC Header for Front Panel (9-pin): AUDIO1 These headers connect to Front Panel Line-out, MIC connector with cable. AUDIO Pin 1 Line-Out, MIC Headers (2) USB Port Headers (9-pin): USB1/USB2 These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel.
Page 15
P W R L E D P i n 1 J W F P S P E A K P i n 1 P i n 1 S y s t e m C a s e C o n n e c t i o n s (8) FAN Power Headers: SYSFAN1 (3-pin), CPUFAN (4-pin) These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different.
Page 16
(10) HDMI-SPDIF Out header: HDMI_SPDIF The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby digital decoder. Use this feature only when your stereo system has digital input function. Some of the VGA Card need connect SPDIF-IN Connector,so its HDMI Port can make sounds .
3-3 Jumper Setting (1) Keyboard/USB function Enabled/Disabled: JP1 2-3 Closed K/B,USB Power ON Enabled 1-2 Closed K/B,USB Power ON Disable (Default) Keyboard & USB Power On Setting (1) CMOS RAM Clear (3-pin): JBAT A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2 pins of JBAT to store the CMOS data.
Chapter 4 Useful Help 4-1 How to Update BIOS Step1. Prepare a boot disc. (You may make one by click START click RUN type SYS A: click OK) Step2. Download upgrade tools and the latest BIOS files of the motherboard from official website and then make a copy of it to your bootable floppy disk after decompressing these files Step3.
Page 19
Power Supply Mold As a result of the increasing power consumption demand from many AMD CPUs in current market, we suggest not to use a CPU that demands more than 65W power consumption at work for an AMD CPU compliant board that comes with power supply design...
Page 20
Subject 2: Suggestion on choosing electric fan Both the amount of electric current to MOSFET and the heat produced from the motherboard go up as AMD‟s CPU power consumption increases. In this case we recommend users select a CPU fan with air outlet towards MOSFET so that CPU fan can carry away heat produced by MOSFET, for better heat dissipation effects.