Table of Contents
Advertisement
Quick Links
USER'S MANUAL
Of
AMD 880G & AMD SB750
Based
M/B for AMD Socket AM3+ Series
Processor
NO. G03-TA98MG-F
：
Rev
2.0
Release date: November 2, 2011
Trademark:
* Specifications and information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AMD 880G
Summary of Contents for AMD 880G
- Page 1 USER'S MANUAL AMD 880G & AMD SB750 Based M/B for AMD Socket AM3+ Series Processor NO. G03-TA98MG-F ： Release date: November 2, 2011 Trademark: * Specifications and information contained in this documentation are furnished for information use only, and are...
- Page 2 Environmental Safety Instruction Avoid the dusty, humidity and temperature extremes. Do not place the product in any area where it may become wet. 0 to 40 centigrade is the suitable temperature. (The figure comes from the request of the main chipset) Generally speaking, dramatic changes in temperature may lead to contact malfunction and crackles due to constant thermal expansion and contraction from the welding spots’...
-
Page 3: Table Of Contents
TABLE OF CONTENT CHAPTER 1 INTRODUCTION OF AMD 880G MOTHERBOARDS FEATURES OF MOTHERBOARD..............1 1-1-1 SPECIAL FEATURES OF MOTHERBOARD .........2 SPECIFICATION ...................3 LAYOUT DIAGRAM ..................4 CHAPTER 2 HARDWARE INSTALLATION HARDWARE INSTALLATION STEPS ............5 JUMPER SETTING ..................5 CPU INSTALLATION ..................6 2-3-1 ABOUT AMD AM3+ CPU SOCKET..........6 2-3-2 CPU INSTALLATION GUIDE............6... -
Page 4: Chapter 1 Introduction Of Amd 880G Motherboards Features Of Motherboard
Introduction of AMD 880G Motherboards Features of motherboard The AMD 880G chipset motherboard series are based on the latest AMD 880G Chipset and the SB 750 chipset which supports the innovative AMD AM3+ FX processors and AMD AM3 processor under 125W power consumption. With a highly-scalable Hyper Transport technology-based system bus up to HT 3.0,... -
Page 5: Special Features Of Motherboard
1-1-1 Special Features of Motherboard CPU Smart Fan—Noise Management System It’s never been a good idea to gain the performance of your system by sacrificing its acoustics. CPU Smart Fan Noise Management System is the answer to control the noise level needed for now-a-day’s high performance computing system. The system will automatically increase the fan speed when CPU operating loading is high, after the CPU is in normal operating condition, the system will low down the fan speed for the silent operating environment. -
Page 6: Specification
AMD 880G North Bridge Chipset Chipset AMD SB750 South Bridge Chipset AMD AM3+ Socket Support AMD AM3+ FX processors and AMD AM3 Phenom™ II processor/Athlon™ II X processor (CPU CPU Socket power consumption should be under 125W) Support HT 3.0... -
Page 7: Layout Diagram
DVI Port ATX Power Conn. Socket AM3+ HDMI port USB 2.0 Ports SYSFAN2 Header SYSFAN1 RJ-45 Over Header AMD 880G USB 2.0 Ports Chipset Audio Connector Gigabit LAN Chip JBAT PCI Express 2.0 x16 by 16 Lane Slot PCI Slot 6-CH... -
Page 8: Chapter 2 Hardware Installation
Chapter 2 Hardware Installation WARNING! Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. Hardware Installation Steps Before using your computer, you had better complete the following steps: 1. -
Page 9: Cpu Installation
KB/USB Power On Setting 2-3 CPU Installation 2-3-1 About AMD AM3+ CPU Socket This motherboard provides an AM3+ socket that supports compatible AMD AM3/AM3+ processor. The CPU that comes with the motherboard should have a cooling FAN attached to prevent overheating. If this is not the case, then purchase a correct cooling FAN before you turn on your system. -
Page 10: Memory Installation
4. Open the socket by 6. Put the level to the 5. Insert compatible CPU pulling the level into CPU socket and see original place of the sideways away from the to it that CPU Pin-1 socket. Make sure that socket and then upwards should be matched into the notched corner... -
Page 11: Expasion Card Installation
NOTE! When you install DIMM module fully into the DIMM socket the eject tab should be locked into the DIMM module very firmly and fit into its indention on both sides. 2-5 Expansion Card Installation 2-5-1 Expansion Slot The board provides one PCI-Express2.0 x16@16 lane graphic slot offer 8Gbyte/sec data transfer rate at each relative direction and up to 16Gbyte/sec concurrent bandwidth at full speed. -
Page 12: I/O Back Panel Connectors
Chapter 3 Connectors & Headers 3-1 I/O Back Panel Connectors RJ-45 LAN Port PS/2 Mouse Port Line-IN VGA Port HDMI Port DVI Port Line-OUT PS/2 Keyboard Port MIC-IN USB 2.0 Ports (1) PS/2 Keyboard & Mouse Connectors: KB1 The green connector above is a standard PS/2 mouse connector for PS/2 mouse. -
Page 13: Internal Connectors
3-2 Internal Connectors (1) Power Connector (24-pin block): ATXPWR1 ATX Power Supply connector: This is a new defined 24-pins connector that usually comes with ATX case. The ATX Power Supply allows using soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard. -
Page 14: Internal Headers
(2) ATX 12V Power Connector (8-pin block): ATX12V This is a new defined 8-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully supports Socket AM2+/AM3 processor must including this connector for support extra 12V voltage to maintain system power consumption. - Page 15 (2) USB 2.0 Port Headers (9-pin): USB1/USB2 These headers are used for connecting the additional USB 2.0 port plug. By attaching an option USB cable, your can be provided with two additional USB 2.0 plugs affixed to the back panel. Pin 1 USB Port Headers (3) Speaker connector: SPEAK1...
- Page 16 CPUFAN SYSFAN1 SYSFAN2 FAN Power Headers (9) Serial COM Port header: COM1 COM1 is the 9-pin block pin-header. Pin1 Serial COM Port 9-pin Block (10) HDMI-SPDIF Out header: HDMI_SPDIF The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby digital decoder.
-
Page 17: Chapter 4 Useful Help
Chapter 4 Useful Help 4-1 How to Update BIOS Solution1: Updating BIOS under DOS: 1. Prepare a bootable disk. (You may make one by click START click RUN type SYS click OK) 2. Download upgrade tools and the latest BIOS files of the motherboard from official website and then make a copy of it to your bootable floppy disk after decompressing these files 3. -
Page 18: Appendix
Power Supply Mold As a result of the increasing power consumption demand from many AMD CPUs in current market, we suggest not to use a CPU that demands more than 65W power consumption at work for an AMD CPU compliant board that comes with power supply design... - Page 19 Subject 2: Suggestion on choosing electric fan Both the amount of electric current to MOSFET and the heat produced from the motherboard go up as AMD’s CPU power consumption increases. In this case we recommend users select a CPU fan with air outlet towards MOSFET so that CPU fan can carry away heat produced by MOSFET, for better heat dissipation effects.
- Page 20 Subject 3: Thunder Protection Feature Introduction: Thunder is such formidable natural force that it can render massive damage to electronic products of all kinds. In thunderstorm season computer systems without powerful thunder protection designs are vulnerable to electric surge damage. High-priced building with thunder protection measures may be a good choice, but usually costly and with corners uncovered.
Need help?
Do you have a question about the 880G and is the answer not in the manual?
Questions and answers