Table of Contents
Advertisement
Quick Links
12 ft x 12 ft / 3.66 m x 3.66 m cosmos Pergola
IMPORTANT. PLEASE READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE
If you experience any product malfunction, defect or are missing any parts,
please contact our customer service department at 1-855-586-8118 or
servicec @ taipengchina.com. Our hours of operation are Monday - Friday,
8:30 AM to 5:30PM EST.
Assembly Manual
ITM. / ART.
2127018
01
01
Advertisement
Table of Contents
Related Manuals for Taipeng 2127018
Summary of Contents for Taipeng 2127018
- Page 1 Assembly Manual 12 ft x 12 ft / 3.66 m x 3.66 m cosmos Pergola ITM. / ART. 2127018 IMPORTANT. PLEASE READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE If you experience any product malfunction, defect or are missing any parts, please contact our customer service department at 1-855-586-8118 or servicec @ taipengchina.com.
- Page 2 SAFETY INFORMATION For the best assembly and usage experience, please read through all steps before attempting to assemble, operate or install the product • WARNING: It is the consumer’s responsibility to comply with any building codes, ordinances, zoning limitations, or local homeowner’s restrictions and obtain any required permit, before purchase and installation of the products.
- Page 3 Components Post Post Corner Crossbeam Left Crossbeam Right Crossbeam Left Crossbeam Right Crossbeam Left Crossbeam Right Decoration Cap Track Beam Top Crossbeam Left Inclined Strut Right Inclined Strut Crossbeam Connector Crossbeam Connector...
- Page 4 Crossbeam Connector Top Crossbeam Shield Track Beam Shield Crossbeam Shield Crossbeam Shield Base Base Cover Left Cloth-inserted Pipe Right Cloth-inserted Pipe Fixed Tube Roof Sidewall Draw Cord Pulley...
- Page 5 Pulley Hardware Bolt\Flat Washer (m6*15) Bolt\Plastic Washer (m6*115) Bolt\Flat Washer (m6*30) Bolt (m6*15) Bolt (m6*15) Allen Wrench Hanger Expansion bolt Allen Wrench Sleeve Wrench Allen Wrench...
- Page 6 Step 1 Fig 1 Fig 2 1.1. Insert the Post (A) into the Base Cover (I) and connect it to the Base (H) with Bolt (AA). See Fig 1. 1.2. Connect the Post Corner (B) to the Post (A) with Bolt (AA), please pay attention to the installation direction.
-
Page 7: Table Of Contents
Step 2 C/C2 C/C2 x12 pcs Fig 3 Fig 4.1 C/C2 C1/C3 C/C2 C1/C3 Fig 4.2 Fig 4.3 Leave the hole, do not put on the Bolt C/C1/C2/C3 C1/C3 C/C2 Fig 4.4 Fig 5 2.1.Slide the Hanger (GG) into the Mosquito net Rod above the Crossbeam Left (C/C2). -
Page 8: X12 Pcs
Step 3 x12 pcs Fig 6 Fig 7.1 Fig 7.2 Fig 7.3 Fig 7.4 3.1.Slide the Hanger (GG) into the Mosquito net Rod above the Crossbeam (C4/C5). See Fig 6. 3.2. Insert the Crossbeam Connector (F) into the Crossbeam Left (C4) and connect them with Bolt (AA). Insert the Crossbeam Connector (F) into the Crossbeam Right (C5) and connect them with Bolt (AA). - Page 9 Step 4 Fig 8.1 6PCS Fig 8.2 Fig 8.3 Fig 8.4 4.1. Insert the Pulley (O) into the Track Beam (D). See Fig 8.1. 4.2. Insert the Crossbeam Connector (F2) into the Track Beam (D) and connect them with Bolt (AA). Insert the Track Beam Shield (G1) into the Track Beam (D).Connect the Track Beam (D) and Track Beam Shield (G1) to the Crossbeam Connector (F2) with Bolt (AA).
- Page 10 Step 5 6PCS Fig 9.1 Fig 9.2 Fig 9.3 Fig 9.4 5.1. Insert the Pulley (N) into the Track Beam (D). See Fig 9.1. 5.2. Insert the Crossbeam Connector (F2) into the Track Beam (D) and connect them with Bolt (AA). Insert the Track Beam Shield (G1) into the Track Beam (D).Connect the Track Beam (D) and Track Beam Shield (G1) to the Crossbeam Connector (F2) with Bolt (AA).
- Page 11 Step 6 Fig 10.1-Fig 10.3 Fig 10.1 Fig 10.2 Fig 10.3 6. Insert the Crossbeam Connector (F) into the Top Crossbeam (D1) and connect them with Bolt(AA). Insert the Top Crossbeam Shield (G) into the Top Crossbeam (D1). Connect the Top Crossbeam (D1) / Top Crossbeam Shield (G) to the Crossbeam Connector (F) with Bolt (AA).
-
Page 12: Aa C/C2
Step 7 C/C1/ C2/C3 Fig 11 C1/C3 C/C2 Fig 12.1 Fig 12.2 7.1. Connect the Post Corner (B) to the Crossbeam (C/C1/C2/C3) with Bolt (AA). See Fig.11. 7.2. Connect the Left Inclined Strut (E) to the Crossbeam Left (C/C2) and the Post (A) with Bolt (AA). See Fig 12.1. - Page 13 Step 8 Fig 13.1 Fig 13.2 Fig 14.2 Fig 14.1 8.1. Connect the Post Corner (B) to the Crossbeam (C4/C5) with Bolt (AA). See Fig 13.1-13.2. 8.2. Connect the Right Inclined Strut (E1) to the Crossbeam Right (C5) and the Post (A) with Bolt (AA). Connect the Left Inclined Strut (E) to the Crossbeam Left (C4) with Bolt (AA).
-
Page 14: C1/C3
Step 9 C/C2 C/C1/C2/C3 C1/C3 Fig 15.1 Fig 15.2 9. Connect the Track Beam (D) to the Crossbeam (C/C1/C2/C3) with Bolt (BB). See Fig 15.1-15.2. BBx6... -
Page 15: Fig 16
Step 10 C/C1/C2/C3 Fig 16 10. Connect the Top Crossbeam (D1) to the Crossbeam (C/C1) with Bolt (BB). See Fig 16. BBx8... -
Page 16: Fig 17
Step 11 Fig 17 C2/C3 Fig 18... - Page 17 J/J1 Fig 19 C/C1 Fig 20 11.1. Connect the Left Cloth-inserted Pipe (J) to the Right Cloth-inserted Pipe (J1). See Fig17. 11.2. Insert the Fixed Tube (J2) into the Roof (K), then connect them to the Crossbeam (C2/C3) with Bolt (CC). See Fig18. 11.3.
- Page 18 Step 12 C/C1/C2/C3/C4/C5 Fig 21 12. Hang the Sidewall (L) on the crossbeam using the Hanger (GG) preassembled on the crossbeam. See Fig 21.
- Page 19 Step 13 Fig 22 13.Using an electric concrete drill, drill holes into the concrete floor, corresponding to the holes in Base (H). Insert Expansion bolt (HH) into the holes and hammer into place, using a hammer. Fasten Expansion bolts (HH), make sure the base (H) are totally grounded.See Fig 22.
- Page 20 CARE AND MAINTENANCE • For cleaning, use a mild detergent solution, rinse with water, and allow to air dry. Do not use acetone, abrasive, or other special detergents as they would be harmful to the product’s finish. • Due to the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched.