3DGence DT3 Manual
  1. Manuals
  2. Brands
  3. 3DGence Manuals
  4. 3D Printers
  5. DT3
  6. Manual

3DGence DT3 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
3DGence DT3
Jet action cleaning

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DT3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for 3DGence DT3

Summary of Contents for 3DGence DT3

  • Page 1 3DGence DT3 Jet action cleaning...

  • Page 2: Rules For Safe Operation

    Jet action cleaning Rules for Safe Operation Important: Do not attempt to operate the 3DGence DT3 until you have read thoroughly and understand all instructions and safety rules contained in this manual. Failure to comply may result in personal injury.

  • Page 3: Technical Specifications

    3DGence DT3 3DGence DT3 Jet action cleaning Jet action cleaning Technical Specifications Outside machine dimensions: 49 cm height 60 cm width 55 cm depth Inside tank dimensions: 28 cm height 31 cm width 25.4 cm depth Tank holds: 22.7 liters of water...

  • Page 4: Installation

    1. Selecting a location 3. Connecting the drain Select a clean, dry, well-lighted area with a The 3DGence DT3 drain is located at the rear of the minimum clearance of six inches between the unit (see Figure 2). Install a standard 19mm inside 3DGence DT3 and any adjacent walls.

  • Page 5: Operation

    3DGence DT3 3DGence DT3 Jet action cleaning Jet action cleaning Operation Lit when Lit when pump is on heater is on Temperature display On when running Up and Down keys Advance key Infinity key Returns Pressing at the same time to the Home Page.
  • Page 6 Note that there is a level switch approximately 2.5cm below the top of the tank. The 3DGence DT3 will not operate if the water level drops below this switch.

  • Page 7: Maintenance

    flow. 2ea 1/4-20 nuts 2ea 10-32 BHCS (1) Unplug and drain the 3DGence DT3 per the strainer Operating instruction step 10 (remember to wear safety protection).
  • Page 8 IMPORTANT: To immediately power off the 3DGence rate. ALWAYS add concentrate to water, NEVER add DT3 (in case of emergency), turn the power switch water to concentrate. off and unplug the power cord.
  • Page 9 Dry parts with paper towels or let enough to handle the full capacity of 3DGence DT3. air-dry. At that point mix in 270 ml of malic acid and dispo- The solution may be used for cleaning additional parts.

  • Page 10: Troubleshooting

    3DGence DT3 Jet action cleaning Jet action cleaning Troubleshooting If 3DGence DT3 does not run - no power to the display. l• Verify the power switch is turned on, the system is plugged into a power source, and that power is available.
  • Page 11 Technical support • If the 3DGence DT3 is no longer under warranty and no service contract has been purchased, there may be a charge for tech support calls. Customers will be made aware of these charges at the time of the call.

  • Page 12: Warranty Information

    3DGence may request that the Customer allow such remote access to the product. In the maintenance of the product, 3DGence may use new or equivalent to new parts or assemblies to the product. In the maintenance of the product, 3DGence may use new or equivalent to new parts or assemblies for equal or improved quality.
  • Page 13 3DGence DT3 Jet action cleaning Notes:...

Table of Contents