1. Technical specifi cations 1.1. TWIN QPSK-PAL CI ref. 553701 Input VSWR (75 ohm): > 7 dB (950 - 2150 MHz) 13/17V (±0.5 V) / OFF LNB Powering (1 unit): 22KHz (±2KHz) (Select. ON/OFF) Input symbol rate: 2 - 42,5 Mbaud Input through losses: <...
Page 6
TWIN QPSK - PAL CI 1.2. Technical specs. Broaband Amplifi ers Frequency range: 46 ... 862 MHz Connector: “F” Gain: 44 ± 2,5 dB Power supply: 24 V Amplifi er 5575 Regulation margin: 20 dB Consumption at 24 V 450 mA Output level (60 dB): 105 dBμV (42 CH CENELEC) Test socket:...
TWIN QPSK - PAL CI 3. Mounting 3.1. Wall mounting IF satellite 553701 5629 5575 input CLAC! 5071 5239 UPSU120 Output 4061 7234 NOTE: The use of both PSU power outputs is recommended to balance the consumption. For example, 4+3 or 3+4...
TWIN QPSK - PAL CI 4. Elements description 4.1. Introduction The TWIN QPSK-PAL CI unit allows the user The unit allows access to scrambled services by The TWIN QPSK-PAL CI unit features: trasmodulate two channels (TV or radio) selected using a conditional access module (CAM) that from those in two satellite transponders in the performs the service’s descrambling.
4.2. TWIN QPSK-PAL CI CTRL CAM PRGM Insert the smartcard completely into the CAM slot. Card contacts looking left and forwards. 1. IF satellite input 6. Status LED 2. IF satellite output 7. Control BUS connectors 3. RF input 8. Baseband audio/video outputs 4.
TWIN QPSK - PAL CI 4.3. Power supply unit Connectors to power the modules (1) On LED 24V: OK 0V: Overload or short circuit UPSU120 Mains input 230V~ NOTES: - The PSU can power up to 6 modules with CAM plus an extra module with CAM powering a LNB. - Whenever the demand of power exceeds 4A (max.
4.4. Broadband amplifi er OPTION “A” - 5575 OPTION “B” - 451202 TEST (-30dB) +10 dB OK - MATV 20 dB 20 dB 10 dB 10 dB 20 dB MATV OK - Return USO EXCLUSIVO EN INTERIOR C. Ret C. Ret FOR INDOOR USE ONLY ¡¡¡ATENCIÓN!!! NO ABRIR.
TWIN QPSK - PAL CI 4.5. Universal Programmer The programmer features 4 buttons: (short press) - Selection of parameter (positioning of the cursor). P C T 4 . 0 Modifi cation of the parameter chosen by U N I V E R S A L the cursor (fl ashing) (short press) - Change menu...
5. - Instructions for use 5.1. Main Menu The frequency ranges from 46 to 862 MHz. The output level can be modifi ed from 99 down to Connect the controller to the front socket of To switch between A and B modules of the 00, and set to OFF.
Page 16
TWIN QPSK - PAL CI b. Input Menu c. Service Menu d. Audio Menu The next menu allows selection of the following: This menu displays the name of the service There are two modes of operation for selecting the - Input frequency (950-2150 MHz) selected together with the number of services audio service: language and index (see point 5.2.b - QPSK input baud rate (2-42.5 Mbaud)
Page 17
NOTE: Sometimes it is not broadcasted the identity of ‘eng’ English the audio language (e.g. it is sent “---” instead ‘fra’ French of “eng”), in which case the receiver is not able ‘den’ Danish to recognize the selected language. In these ‘nor’...
Page 18
TWIN QPSK - PAL CI ****** R will be modulated by the audio sub-carrier. If an option other than 5.5 MHz is selected from the audio subcarrier’s menu, then the signalling is always mono, and the following options wil be displayed: In dual mode, L will be modulated by 5.5 MHz and R by 5.74 MHz.
e. Measurements Menu f. Temperature Menu 5.2. Extended Menu This menu displays an estimated value of the BER This menu indicates the current temperature on a When the key is held down for more than 3 (Bit Error Rate before Viterbi decoding) . scale of 1 to 10, as well as the maximum recorded seconds the unit displays a series of less frequently along its working time.
Page 20
TWIN QPSK - PAL CI b. Audio Mode Menu c. Modulator 1 Menu - Subt. OFF: All subtitles deactivated. - Ttx. Subt: aut: Teletext subtitles only (automatic or page selected by user). This menu allows the selection of the manner in This menu displays...
Page 21
d. Modulator 2 Menu Audio sub-carrier to video carrier ratio: allows selection of audio sub-carrier level relative to video Once opened this menu, it displays: carrier; possible values are: - Audio level - Audio subcarrier-to-Video carrier ratio -18dB -22dB. - Video format. -20dB -24dB.
TWIN QPSK - PAL CI 5.3. Saving Parameters The time taken to carry out the process will depend on the number of QPSK multiplex services. Once the desired value has been selected in any Finally, the LEDS indicate the following operating of the menus (normal or extended), in order to conditions: save the information, hold down the...
6. - Controlling the Device Menu structure This version of the TWIN QPSK-PAL CI unit allows confi guration and monitoring via a PC for both local and remote procedures. a. Local control Long The “Headend Management” programme (v2.14 press or higher) is required, as well as a special cable (provided with the programme) that connects a PC serial port to the “PRGM”...
TWIN QPSK - PAL CI 7. Application example Distribution of 42 channels of TWIN QPSK-PAL CI 75 ohm 4061 Quattro 5629 5629 7 x 553701 7 x 553701 5151 451202 5629 7 x 553701 RF output The diagram shows a headend to process 42 TV channels from a QPSK transmission There can be identify the BUS control that interconnects all TWIN QPSK-PAL CI units for which operation it is nesessary to include a Headend Controller unit 5559 or 555901 and corresponding software.
8. Norms for rack mounting (max. 49 TWIN QPSK-PAL CI - 7 subracks with 5 units in height - 8,7”) 8.1. Installation of the rack with These ventilators will be installed on a tray that is fi xed inside the cabinet (fi g. 1 & 2). This way, the ventilation facilities ventilators will force the fresh air entering from the base of the cabinet, to circulate between the...
Page 26
TWIN QPSK - PAL CI 8.2. Installation of the rack without It is very important that this process operates correctly, therefore the following must be ventilation facilities observed: - Do not open the side doors, as this would cause To install the units in racks without installation the ventilators to extract the air from the outside facilities, and when the rack is located in a place rather than the air inside the rack.
9. Norms for cabinet mounting IMPORTANT EXTRACTOR for forced ventilation must be onto The scheme of recommended the highest module. ventilation is the one in the fi gure in any case of cabinet placement (horizontal or vertical). Maximum environment temperature: 45ºC. Horizontal The maximum temperature placement...
Page 28
TWIN QPSK - PAL CI IMPORTANT Horizontal placement of the cabinets is strongly recommended, hanging them as HORIZONTAL near to the fl oor as possible. If the horizontal placement is impossible, 0,2 m 0,2 m then vertical placement is allowed. Respect the recommended minimum distances in the attached schemes.
Page 33
Guarantee Televés S.A. offers a two year guarantee, beginning from the date of purchase for countries in the EU. For countries that are not part of the EU, the legal guarantee that is in force at the time of purchase is applied. Keep the purchase invoice to determine this date. During the guarantee period, Televés S.A.