Program Parameters For Operating Mode - Carrier MOTORMASTER 48/50P3 Installation Instructions Manual

PARAMETERS
P01 Line Voltage: 01 = low line, 02 = high line
P02 Carrier Freq: 01 = 4 kHz, 02 = 6 kHz, 03 = 8 kHz
P03 Startup mode: flying restart
P04 Stop mode: coast to stop
Standard Speed source: 01 = keypad, 04 = 4-20mA (NO PI), 05 = R22 or R410A,
P05
06 = R134a
P06 TB-14 output: 01 = none
P08 TB-30 output: 01 = none
P09 TB-31 Output: 01 = none
P10 TB-13A function sel: 01 = none
P11 TB-13B function sel: 01 = none
P12 TB-13C function sel: 01 = none
P13 TB-15 output: 01 = none
P14 Control: 01 = Terminal strip
P15 Serial link: 02 = enabled 9600,8,N,2 with timer
P16 Units editing: 02 = whole units
P17 Rotation: 01 = forward only, 03 = reverse only
P19 Acceleration time: 20 sec
P20 Deceleration time: 10 sec
P21 DC brake time: 0
P22 DC BRAKE VOLTAGE 0%
P23 Min freq = 8 Hz ~ 100 – 160 rpm
P24 Max freq
P25 Current limit: (%)
P26 Motor overload: 100
P27 Base freq: 60 or 50 Hz
P28 Fixed boost: 0.5% at low frequencies
P29 Accel boost: 0%
P30 Slip compensation: 0%
P31 Preset spd #1: speed if loss of control signal
P32 Preset spd #2: 0
P33 Preset spd #3: 0
P34 Preset spd 4 default — R22 setpoint. TB12-2 open
P35 Preset spd 5 default — R134a setpoint. TB12-2 closed
P36 Preset spd 6 default
P37 Preset spd 7 default
P38 Skip bandwidth
P39 Speed scaling
P40 Frequency scaling 50 or 60 Hz
P41 Load scaling: default (not used so NA)
P42 Accel/decel #2: default (not used so NA)
P43 Serial address
P44 Password:111
Speed at min signal: 8 Hz; used when PID mode is disabled and 4-20 mA input is
P45
at 4 mA
Speed at max feedback: 60 or 50 Hz. Used when PID disabled and 4-20 mA input is
P46
at 20 mA
P47 Clear history? 01 = maintain. (set to 02 to clear)
P48 Program selection: Program 1 – 12
P61 PI Mode: 05 = reverse, 0-5V, 01 = no PID
P62 Min feedback = 0 (0V *10)
P63 Max feedback = 50 (5V * 10)
P64 Proportional gain = 3.5%
P65 Integral gain = .2
P66 PI accel/decel (setpoint change filter) = 10
P67 Min alarm
P68 Max alarm
LEGEND
NA — Not Applicable
PI — Proportional Integral
PID — Proportional Integral Derivative
Table 5 — Program Parameters for the Operating Mode
DESCRIPTION
14
MODE 1 MODE 2 MODE 4
01 02 02
01 01 01
06 06 06
01 01 01
05 05 05
01 01 01
01 01 01
01 01 01
01 01 01
01 01 01
01 01 01
01 01 01
01 01 01
02 02 02
02 02 02
01 01 01
20 20 20
10 10 10
0 0 0
0 0 0
8 8 8
60 60 50
125 110 110
100 100 100
60 60 50
0.5 0.5 0.5
0 0 0
0 0 0
57 57 47
0 0 0
0 0 0
24.0 24.0 24.0
12.6 12.6 12.6
0 0 0
0 0 0
0 0 0
0 0 0
60 60 50
200 200 200
60 60 60
1 1 1
111 111 111
8 8 8
60 60 50
01 01 01
01 02 04
05 05 05
0 0 0
50 50 50
3.5 3.5 3.5
.2 .2 .2
10 10 10
0 0 0
0 0 0