Bosch Professional GTS 254 Original Instructions Manual page 18

18 | English
Technical data
Table saw
Article number
Rated power input
No-load speed
Starting current limitation
Weight according to EPTA-Procedure 01:2014
Protection class
Dimensions (including detachable parts of the tool)
Width x depth x height
Dimensions of suitable saw blades
Saw blade diameter
Base blade thickness
Min. tooth thickness/offset
Hole diameter
Maximum workpiece dimensions: (see "Maximum workpiece dimensions", page 22)
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Table saw with mounted saw blade (28)
– "Power tool" fastening set (39) (8 fastening screws, 8
washers)
– Base unit (14)
– "Base unit" fastening set (37) (16 fastening screws, 16
washers, 16 securing rings, 16 nuts)
– Tilt protector (13)
– "Tilt protector" fastening set (38) (4 fastening screws, 8
washers, 4 securing rings, 4 nuts)
– Angle guide (3)
– Profile rail (50)
– "Profile rail" wing nut (51)
– Parallel guide (9)
– Additional parallel guide (47)
– "Additional parallel guide" fastening set (48) (2 fastening
screws, 2 wing nuts)
– Riving knife (27) with protective cover (6) fitted
– Anti-kickback pawls (7)
– Ring spanner (35)
– Hook spanner/open-ended spanner (36)
1 609 92A 72G | (29.10.2021)
GTS 254
3 601 M45 080
3 601 M45 0L0
3 601 M45 0K0
3 601 M45 0F0
W 1800
-1
min 4300
kg 24.4
/ II
mm 690 x 620 x 1000
mm 254
mm < 1.8
mm > 2.4
mm 25.4
– Push stick (15)
– Table insert (8)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Stationary or flexible mounting
To ensure safe handling, the power tool must be
u
mounted on a flat, stable work surface (e.g. work
bench) before use.
Assembly with base unit and tilt protector
(see figures a1−a3)
For assembly, use the "base unit" (37), "tilt protector" (38)
and "power tool" (39) fastening sets
– Screw the base unit (14) together. Tighten the screws
firmly.
– Screw the tilt protector (13) to the base unit.
– Place the power tool on the base unit so that the tilt pro-
tector points to the rear.
– Attach the power tool to the base unit. For this, use the
lateral holes (31) of the power tool as well as the holes in
the base unit.
GTS 254
3 601 M45 0C0
1800
3800
● ●
24.4
/ II
690 x 620 x 1000
254
< 1.8
> 2.4
25.4
Bosch Power Tools