Trane CH530 Installation, Operation And Maintenance Manual page 21

Tools Required
Common hand tools and hand-held power tools are
required to perform the retrofit. A trained service
technician with a well-stocked tool chest should have all of
the necessary tools to perform the job. The following list
is a sampling of the tools that one could expect to find
inside the technician's tool chest:
• Electric drill and bit set
• Hacksaw or reciprocating saw
• Extension cord
• Screwdrivers
• Wrenches
• Ratchet and socket set
• Torque Wrench
• Nut driver set
• Wire cutter
• Wire stripper
• Digital multi-meter, with phase detection capability
The following special tools are also required to perform
the retrofit:
Note: Some field provided material will be required to
perform the replacement. This is a partial list in
addition to normal service tools and hardware.
• Overhead or Portable Hoist (minimum 2-ton rated
capacity)
• Spreader Bar
• Type A to Type B USB cable
• Computer having Tracer™ TU version 4.0 or newer
Additional Components
Additional components may be required to perform the
AFDK retrofit. These components depend on the options
selected and the existing equipment. A list of additional
components available from Trane is provided in
Some of these components may be added to an order
depending on the model number selected.
AFDK-SVU01C-EN
Table 2. Options and accessories
Item Part Number Description
1 20600790100
2 20600080100
3 20600090100
Table 2.
4 20600880100
5 20600890100
6 20600900100
7 20600910100
8 HSE01285
9 HSE01286
10 HSE01287
11 CHM00481
12 PAI00061
In addition to the required components listed in
motor brushes may optionally be installed. Motor brushes
reduce the wear on compressor motor bearings due to the
additional stresses from the application of adjustable
Drive and Cabinet
Kit; Valve and Hardware kit for AFDK
Corrosion Inhibitor
Low pressure transducer; (PX) 0–50 PSIA,
with integral male global connector
Branching cable; Male to two Female, 39.37
inches long
Extension cable; Male to Female, 39.37 inches
long
Shorting buss bar kit; contains 3 bars and 12
x 0.75-16 in. hex jam nuts
Shorting buss bar kit; contains 3 bars and 12
x 0.75-16 in. hex jam nuts
Shorting buss bar kit; contains 3 bars and 12
x 0.75-16 in. hex jam nuts
Shorting buss bar kit; contains 3 bars and 12
x 1.12-12 in. hex jam nuts
Strainer; 3/4 NPTI x 3/4 NPTI w/drain
Valve; Ball, 3/4 copper to copper
Bushing; 1 NPTE x 3/4 NPTI
Adapter; 3/4 FTG x 1/2 M
Adapter; 3/4 FTG x 3/4 M
Adapter; 3/4 FTG x 3/4 F
Valve; Ball, 1/4 copper to copper
Adapter; 1/4 FTG x 1/4 F
Hardware; Primary Loop Fittings
Adapter; 3/4Female JIC Flare X 3/4 ID Hose 8
Elbow; 3/4NPTE X 3/4 Male JIC Flare, 90°
Clamp; Hose—1.00 ID
Adapter; 3/4NPTI X 3/4 Male JIC Flare
Elbow; 3/4Female JIC Flare X 3/4 Male JIC
Flare, 45°
Elbow; 3/4NPTE X 3/4 Male JIC Flare, 45°
Hardware; Secondary Loop Fittings
Adapter; 3/4Female JIC Flare X 3/4 ID Hose 8
Elbow; 3/4NPTE X 3/4 Male JIC Flare, 90°
Clamp; Hose—1.00 ID
Adapter; 3/4NPTI X 3/4 Male JIC Flare
Elbow; 3/4Female JIC Flare X 3/4 Male JIC
Flare, 45°
Elbow; 3/4NPTE X 3/4 Male JIC Flare, 45°
Assembly; PUMP/HX Water to Water Frame 3 1
Assembly; PUMP/HX Water to Water Frame 4 1
Assembly; PUMP/HX Water to Air Frame 3
Assembly; PUMP/HX Water to Air Frame 4
Hose; 3/4 ID, Rubber, Cloth Braid, 300 PSI
Hose; 3/4 ID, Rubber, Cloth Braid, 300 PSI
Hose; 3/4 ID, Rubber, Cloth Braid, 300 PSI
Corrosion Inhibitor
Paint; Executive Beige, Spray
Qty
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
4
8
1
1
4
1
4
8
1
1
4
1
1
30
FT
60
FT
120
FT
1
1
Table 2,
21