Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Daewoo DSB-F154LH
Summary of Contents for Daewoo DSB-F154LH
- Page 1 OWNER'S MANUAL MODEL #: DSB-F154LH S/N : 3113909901...
-
Page 2: Safety Instructions
The installation instructions are for a experienced installer. If you are not an experienced installer, contact a local installer for help. If you require help with service, contact your certified dealer or Daewoo Electronics for additional instructions. If Unit is Installed Improperly:... -
Page 3: Location Of Controls
LOCATION OF CONTROLS INDOOR UNIT Deodorizing Filter Removes bad Air In smells from the air. Indoor Cover Air Cleaning Filters Removes dust and prohibits germs. AIR OUT Fan Direction (Left/Right) OUTDOOR UNIT AIR IN AIR OUT Electric Dust Collector Emergency/ (Air clean Plasma) Remote Switch Removes small dust and... -
Page 4: Indoor Unit Display
INDOOR UNIT DISPLAY Indoor Unit Display Remote Control Signal Receiver This place is the part to receive the signal if it receives the signal, you can hear the signal “beep. beep”. (DSB-F154AH) (DSB-F154LH) TIMER QUICK OXYGEN ON (Red) Timer (Yellow) -
Page 5: Remote Controller
REMOTE CONTROLLER DSB-F154LH FAN SPEED Button Press to select the fan speed (High " ", Middle " ", Low " ", Natural). MODE Button Press to cycle through the modes (Auto/Quick/Cool/Fan/Dehumidifier/ Heat) SLEEP Button Press to set the unit for the sleep mode. -
Page 6: Operation
• Use the attached power cord only. • If the outlet is a 3-pronged type or other, have an electrician install a new outlet. • The new air conditioner system should be on it’s own 220V circuit. Contact your local electrical installer for installation. Items Under 12K class AC 250V, 16A, H05VV-Fx1.0m... -
Page 7: Setting The Unit For Remote Operation
SETTING THE UNIT FOR REMOTE OPERATION After the unit is fully connected and plugged in, it can be turned on. To turn the unit on and set it for remote operation, follow the procedures below: 1. Open the indoor unit’s cover and make sure the EMER- GENCY/REMOTE switch is set to the REMOTE position;... -
Page 8: To Set Unit To Cool Mode
SET UNIT TO QUICK MODE To set this unit to cool or heat (Heat pump model only) at the highest power, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON”... -
Page 9: To Operate Only Fan
TO OPERATE ONLY FAN To operate only the fan so the unit will circulate the air, proceed as follows: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON”... -
Page 10: To Select The Fan Direction
TO SET UNIT TO HEAT MODE (ONLY HEAT PUMP MODEL) To set the unit to heat the room to a desired temperature, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON”... -
Page 11: To Set The On Timer Mode
TO SET THE ON TIMER MODE This unit can be set to automatically turn on after a predetermined amount of hours (up to 24) in the order of 0.5, 1, 1.5, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 12, 16, 20, 24. 1. -
Page 12: To Set The Off Timer Mode
TO SET THE OFF TIMER MODE This unit can be set to automatically turn off after a predetermined amount of hours (up to 12) in the order of 0.5, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9, 9.5, 10, 11, 12. 1. -
Page 13: To Set Unit To Sleep Mode
TO SET UNIT TO SLEEP MODE When you are going to sleep, select this feature and the unit will cool off the room to the desired temperature and then increase that temperature throughout the night. 1. Press the ON/OFF button on the remote control to turn the unit on;... -
Page 14: Changing/Cleaning The Air Filters
CHANGING/CLEANING THE AIR FILTERS To change or clean the two black air filters, follow the procedures below: 1. Open the indoor unit’s cover and remove both black air filters by bending them slightly backward and the lifting out. 3. Examine the filters and determine if they need to be cleaned or replaced. -
Page 15: Installing The Remote Bracket
(LH/PH/AH Model Only) 4. Insert cleaned or new small filters (Deodorizing and Electrostatic) back into the unit. After putting the connection terminal into electric dust collector, insert the electric dust colloctor into the unit. (Only DSB-F154LH/154PH/154AH) -
Page 16: Care And Maintenance
CARE AND MAINTENANCE warning • Make sure the AC cord is unplugged and the unit is off before cleaning. • Do not use water on the unit to clean it. This is a shock hazard and the unit can be damaged. Clean the casing and front of the indoor unit with a vacuum brush or wipe with a clean damp cloth. -
Page 17: Troubleshooting Guide
TROUBLESHOOTING GUIDE Before requesting service, please refer to the chart below for possible solutions: SYSPTOMS No power. Power failure. Line voltage too low. Unit is unplugged or not completely plugged in. Unit is off. Batteries in remote are weak or dead. EMERGENCY/REMOTE switch is not set to REMOTE. -
Page 18: Instruction Of Installation
INSTRUCTION OF INSTALLATION Below is an overview for the connection of the Indoor unit to the Outdoor unit. OVERVIEW This appliance must be installed according to national power supply acquirement. 10cm (3.95in) from side wall At least 30cm (11.8in) from unit AC Outlet and Plug 3.9 inches...