Download Print this page
Midwest K9 Kennel K91066 Assembly Instructions Manual

Midwest K9 Kennel K91066 Assembly Instructions Manual

Hide thumbs Also See for K9 Kennel K91066:

Advertisement

Quick Links

800-428-8560
midwesthomes4pets.com
3142 S. Cowan Rd.
Muncie, Indiana 47302
Assembly Instructions for Model Number K91066
Assembly Videos and Instruction Manuals can be viewed at midwesthomes4pets.com.
For instructions in Spanish and French, please visit www.midwesthomes4pets.com.
IMPORTANT INFORMATION
Warning: Remove collars, tags, and leads from pet before placing it in the kennel to prevent possible
entanglement. DO NOT leave young animals unsupervised for extended periods of time. MidWest's main concern is
your pet's well-being. If your pet has never been kept in any enclosure, specific training may be necessary for your pet's
safety. A pet, not specifically trained to be restricted, may attempt to escape from this enclosure, which could cause
serious injury to your pet or damage to this product. MidWest will not accept liability or warrant any loss to improper use
of this product by a pet that has not been properly trained.
Warranty Information
Unwrap and remove all parts from the box. Keep the box and packing material until the product is assembled. In case of
return or exchange, failure to return product in similar condition as received could result in limited reimbursement. Please
save sales receipt as proof of purchase for warranty purposes. Check to ensure you have all the parts below. If you discover
any parts are missing, immediately call our toll-free service helpline at 1-800-428-8560 (Monday - Friday 9 a.m. to 4 p.m.
EST) or at info@midwesthomes4pets.com.
Helpful Hints
Please take time to read and follow these instructions. To make set-up easier, locate a level area to assemble your
kennel. Remove all components from the carton and arrange them as shown on Page 2. You will need a pair of pliers
and an adjustable wrench to assemble your kennel. We recommend two people assemble the kennel together.
The chain-link fence comes in one continuous 32' piece. It is prone to tangle while attaching, but with two people and
a little patience, the fence can applied with minimal complication. The best practice is to unroll the fence and stretch
it out completely to undo any tangling. Then, using two people, lift, pull, and stretch the chain-link fence around the
perimeter one small section at a time.
Sunscreen Safety
Your K9 Kennel comes with a Sunscreen. We suggest removing and storing the Sunscreen when not needed to shade your
pet. Do not allow snow or debris to collect on top of the Sunscreen. Occasionally, even rain will collect. Remove it as soon
as possible. Injury to your pet and damage to your Kennel may occur if the load is not removed. Properly cared for, your
Sunscreen will provide years of service and protection for your pet.
1.

Advertisement

loading
Need help?

Need help?

Do you have a question about the K9 Kennel K91066 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Midwest K9 Kennel K91066

  • Page 1 A pet, not specifically trained to be restricted, may attempt to escape from this enclosure, which could cause serious injury to your pet or damage to this product. MidWest will not accept liability or warrant any loss to improper use of this product by a pet that has not been properly trained.
  • Page 2: Parts Identification

    PARTS IDENTIFICATION Bottom U-Shaped Rail with short corner peg (2) Vertical Tension Rod - 5/16th Diameter (2) Long Filler Rail - swaged on one end (3) Chain-Link Fence (1) Sunscreen Top (1) Medium Filler Rail - Long - three rails have one swaged end; three rails have two swaged ends (6) Short Plastic Ties (70) Short Filler Rail - swaged on one end (3)
  • Page 3 ASSEMBLY INSTRUCTIONS Place the Bottom U-Shaped Rails (A) on the sides as shown. The small pegs on the Bottom U-Shaped Rails must point up. In the front, place a Short Filler Rail (D), Long Filler Rail (B), and the two sections of the Gate Frame (E) on the ground as shown.
  • Page 4 On each corner, push the non-swaged end of a Vertical Corner Post (F) onto the short corner peg of each Bottom U-Shaped Rail. To assemble the middle rail, start at the corner closest to the Gate Frame. Swing the Gate Frame into the upright position.
  • Page 5 Moving to the back, attach a Medium Filler Rail (C) with two swaged ends to the Middle U-Shaped Rail. Swaged Swaged Place the second Middle U-Shaped Rail (G) on the other set of Vertical Corner Posts. Use a Medium Filler Rail (C) with one swaged end to connect the U-Shaped Rail to the Filler Rail from Step 6.
  • Page 6 Complete the middle rail by using a Long Filler Rail (B) to connect the U-Shaped Rail to the Gate Frame. Then, push the non-swaged end of a Vertical Corner Post (F ) onto the short corner peg of each Middle U-Shaped Rail. Swaged To assemble the top rail, start at the corner closest to the Gate Frame.
  • Page 7 Place the second Top U-Shaped Rail (G) on the other set of Vertical Corner Posts. Use a Medium Filler Rail (C) with one swaged end to connect the U-Shaped Rail to the Filler Rail from Step 9. Swaged Moving to the front, use a Long Filler Rail (B) to connect the right side of the Gate Frame to the Top U-Shaped Rail. Swaged...
  • Page 8 Install the Gate Door (I) in the Gate Frame (E). The hinge pins are fixed on the Gate Frame and do not adjust. The hinge knuckles, on the Door, will be loose until you tighten them. Begin by aligning the bottom pin and the bottom knuckle.
  • Page 9 Next, stand one end of the Chain-Link Fence (K) up against the left side of the Gate frame. Starting at the top, thread the Vertical Tension Rod (J) down through the Chain-Link Fence, front/back, front/back, through each diamond, while making sure to pass through the eye of each Eyebolt on the way down. Thread the rod all the way through the last diamond at the bottom.
  • Page 10 After you have unrolled the Chain-Link Fence completely around the frame, you may find that you have several extra inches of wire that extend past the last set of Eyebolts. This excess must be removed. Pull the Chain-Link Fence tightly past the Eyebolts to determine where to remove the extra fencing so that the second Tension Rod can be installed as in Step 15.
  • Page 11 Use pliers to grip the exposed threads and snap off the excess at the scored area of the bolt. Finish each nut with a Plastic Cap (P). Starting at the Gate Frame, install Short Plastic Ties (M) every two feet, securing the Chain-Link Fence to the Top Rail of the Kennel.
  • Page 12: Limited Manufacturer's Warranty

    LIMITED MANUFACTURER’S WARRANTY For one (1) year from the date of original purchase, MIDWEST Homes For Pets (“MIDWEST”) warrants to the purchaser of this kennel that, should it prove defective by reason of improper workmanship and/or material, MIDWEST will repair or replace, at its option, any defective part of the kennel, without charge for the part or for shipping.