Midwest K9 Kennel K91066 Assembly Instructions Manual

Midwest K9 Kennel K91066 Assembly Instructions Manual

Hide thumbs Also See for K9 Kennel K91066:

Advertisement

Assembly Instructions for Model Number K91066

IMPORTANT INFORMATION

Remove collars, tags, and leads from pet before placing it in the kennel to prevent possible entanglement. DO NOT leave young
animals unsupervised for extended periods of time. MidWest's main concern is your pet's well-being. If your pet has never been kept
in any enclosure, specific training may be necessary for your pet's safety. A pet, not specifically trained to be restricted, may attempt
to escape from this enclosure, which could cause serious injury to your pet or this product. MidWest will not accept liability or
warrant any loss to improper use of this product by a pet that has not been properly trained.
Unwrap and remove all parts from the box. Keep the box and packing material until the product is assembled. In case of return or
exchange, failure to return product in similar condition as received could result in limited reimbursement. Please save sales receipt
as proof of purchase for warranty purposes. Check to ensure you have all the parts below. If you discover any parts are missing,
immediately call our toll-free service helpline at 1-800-428-8560 (Monday - Friday 9 a.m. to 4 p.m. EST) or at
info@midwesthomes4pets.com.
For instructions in Spanish and French, please visit www.midwesthomes4pets.com.

PARTS IDENTIFICATION

NOTE: Please take time to read and follow these instructions. To make set-up easier, locate a level area to assemble your kennel.
Remove all components from the carton and arrange them as shown below. You will need a pair of pliers or an adjustable wrench
to assemble your kennel. Two people are needed to assemble the kennel.
A.
Scored Eyebolt (8)
B.
Nut (8)
C.
Black Plastic Cap (8)
D.
Large Black Plastic Tie (50)
E.
Bent Bottom Rail-
with one short corner peg
rails have no swaged ends
F.
Bent Middle Rail
- with one long and one short corner peg
rails have no swaged ends
G.
Bent Top Rail -
with one long corner peg
rails have no swaged ends
F
E
L
(2)
(2)
(2)
N
H
I
J
K
midwesthomes4pets.com
Muncie, Indiana 47308
H.
Long Filler Rail
- swaged on both ends
I.
Short Filler Rail
- swaged on one end
J.
Vertical Corner Post
K.
Vertical Tension Rod - 5/16th Diameter (2)
L.
Gate (1)
M.
Chain-Link Fence (1)
N.
Sunscreen Top (1)
O.
Small Black Plastic Ties (24)
M
G
800-428-8560
P .O. Box 1031
(3)
(3)
(8)
- swaged on one end
The Vertical Corner Posts (J) and Short Filler
Rails (I) have one swaged end (reduced -
smaller diameter). The Long Filler Rails (H)
are swaged on both ends.
A & B
C
D
O
1.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the K9 Kennel K91066 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Midwest K9 Kennel K91066

  • Page 1 A pet, not specifically trained to be restricted, may attempt to escape from this enclosure, which could cause serious injury to your pet or this product. MidWest will not accept liability or warrant any loss to improper use of this product by a pet that has not been properly trained.
  • Page 2 ASSEMBLY INSTRUCTIONS Place the two Bent Bottom Rails, one Long Filler Rail (H), one Short Filler Rail (I), and the Gate (L) on the ground as Swaged shown. The small pegs on the Bent Bottom Rails must point up. Note the placement of the swaged ends on each rail. Swaged Push the swaged ends of the Long Filler Rail (H) into the ends of the Bent Bottom Rails on each side.
  • Page 3 To assemble the middle rail, place the non-swaged, long pegs on the Bent Middle Rail (F) on the swaged tops of the Vertical Corner Posts. Place a Long Filler Rail (H) in the back to connect the first Bent Middle Rail from Step 4 to the second Bent Middle Rail. The non-swaged, long pegs on the Bent Middle Rail with fit on the swaged tops of the Vertical Corner Posts.
  • Page 4 To assemble the top rail, place the long peg on the Bent Top Rail (G) onto the swaged tops of the Vertical Corner Posts. On the side closest to the Gate, the Bent Top Rail will connect with the swaged peg at the top of the Gate. Place the second Bent Top Rail on the Vertical Corner Posts on the opposite side.
  • Page 5 Next, stand one end of the Chain-Link Fence (M) up against the left side of the Gate frame. Starting at the top, thread the Vertical Tension Rod (K) down through the Chain-Link Fence, front/back, front/back, through each diamond, while making sure to pass through the eye of each Eyebolt on the way down.
  • Page 6 After you have unrolled the roll of Chain-Link Fence completely around the frame, you may find that you have several extra inches of wire that extend past the last set of Eyebolts. This excess must be removed. Pull the Chain-Link Fence tightly past the Eyebolts to determine where to remove the extra so that the second Tension Rod can be installed as in Step 10.
  • Page 7 Starting at the Gate Frame, install Large Black Plastic Ties (D) every two feet, securing the Chain-Link Fence to the Top Rail of the Kennel. Do the same with the Middle and Bottom Rails, installing ties every two feet. Sunscreen Installation Unfold the Sunscreen (N) and, using the Small Black Plastic Ties (O), loosely attach it to the Bent Top Rail of the Kennel at each corner.
  • Page 8 LIMITED MANUFACTURER’S WARRANTY For one (1) year from the date of original purchase, MIDWEST Homes For Pets (“MIDWEST”) warrants to the purchaser of this kennel that, should it prove defective by reason of improper workmanship and/or material, MIDWEST will repair or replace, at its option, any defective part of the kennel, without charge for the part or for shipping.

Table of Contents