General Specification - New Holland 5500 Service Manual

Crankcase - General specification
Crank gear
Crankshaft - bearings
Main journal diameter
Main journal undersize
Main bearing wall thickness
Main bearing undersize
Main journal clearance in bearings
• Maximum wear clearance
Crankpin diameter
Crankpin undersize
Big end bearing wall thickness
Big end bearing undersize
Crankpin clearance in big end bearing
• Maximum wear clearance
Crankshaft thrust washer thickness
Thrust washer oversize
Width of main bearing housing over thrust washers
Length of corresponding main journal
Crankshaft end float
• Maximum wear clearance
Maximum main journal and crankpin ovality or taper after
grinding
Maximum main journal and crankpin ovality or taper due
to wear
Maximum main journal misalignment crankshaft resting
on end journals
Maximum misalignment of crankpins relative to main
journals (in either direction)
Tolerance from outer crankpin edge to crankshaft center
line
Maximum crankshaft flange run-out with gauge stylu,
over 108.000 mm (4.252 in) diameter (total gauge
reading)
Maximum flywheel seat eccentricity relative to main
journals (total gauge reading)
Connecting rods
Small end bore diameter
Small end bushing outer diameter
Bushing interference fit in small end
Small end bushing fitted ID
Engine - Engine and crankcase
47899740 24/06/2015
10.1 [10.001] / 6
79.791 - 79.810 mm (3.141 - 3.142 in)
0.254 mm (0.010 in) –
0.508 mm (0.020 in) –
0.762 mm (0.030 in) –
1.016 mm (0.040 in)
2.168 - 2.178 mm (0.085 - 0.086 in)
0.254 mm (0.010 in) –
0.508 mm (0.020 in) –
0.762 mm (0.030 in) –
1.016 mm (0.040 in)
0.034 - 0.103 mm (0.001 - 0.004 in)
0.180 mm (0.007 in)
63.725 - 63.744 mm (2.509 - 2.510 in)
0.254 mm (0.010 in) –
0.508 mm (0.020 in) –
0.762 mm (0.030 in) –
1.016 mm (0.040 in)
1.805 - 1.815 mm (0.071 - 0.071 in)
0.254 mm (0.010 in) –
0.508 mm (0.020 in) –
0.762 mm (0.030 in) –
1.016 mm (0.040 in)
0.033 - 0.087 mm (0.001 - 0.003 in)
0.180 mm (0.007 in)
3.378 - 3.429 mm (0.133 - 0.135 in)
0.127 mm (0.005 in) –
0.254 mm (0.508 in) –
0.508 mm (0.020 in)
31.766 - 31.918 mm (1.251 - 1.257 in)
32.000 - 32.100 mm (1.260 - 1.264 in)
0.082 - 0.334 mm (0.003 - 0.013 in)
0.400 mm (0.016 in)
0.0100 mm (0.0004 in)
0.0500 mm (0.0020 in)
0.0100 mm (0.00039 in)
0.2500 mm (0.00984 in)
± 0.1000 mm (0.0039 in)
0.0250 mm (0.0010 in)
0.0400 mm (0.0016 in)
41.846 - 41.884 mm (1.647 - 1.649 in)
41.979 - 42.017 mm (1.647 - 1.649 in)
0.0950 - 0.1710 mm (0.0037 - 0.0067 in)
38.004 - 38.014 mm (1.496 - 1.497 in)