Crown CT63002HX Original Instructions Manual page 27

Symbol
III
Power tool designation
The power tool is intended for cleaning works using
water jet under pressure (washing of vehicles, garden
tools, paving slabs, etc�)�
Use this power tool for private households only�
Power tool components
1 Outlet fitting (high pressure)
2 Ventilation slots
3 Indicators of the state of battery charge *
4 Control button of the state of battery charge *
5 Battery *
6 Battery lock *
7 Lock button of trigger
8 Pressure switch button with indicator (low / high)
9 Trigger
10 Inlet fitting (low pressure)
11 Sprayer *
12 Sprayer holder *
13 Tube *
14 Quick-release adapter (with valve) *
15 Hose (assembled) *
16 Detergent spray nozzle *
17 Charger *
18 Fixing bush *
19 Quick-release coupling *
20 Float *
21 Holder *
22 Filter *
23 Label *
24 Indicator (red) *
25 Indicator (green) *
26 Swivel head of the sprayer *
Meaning
Unlocked�
Protection class�
Attention� Important�
A sign certifying that the
product complies with es-
sential requirements of the
EU directives and harmo-
nized EU standards�
Useful information�
Do not dispose of the power
tool in a domestic waste
container�
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of power tool
elements
Before carrying out any works on the power tool
remove the battery 5.
Mounting / dismounting / setting-up of
some elements is the same for all power
tool models, in this case specific models
are not indicated in the illustration.
Assembly / disassembly / installation of the
sprayer (see fig. 1-2)
• Move the fixing bush 18 back and hold it in this
position (see fig. 1.1).
• Install the sprayer 11 into the holder 12 (see fig. 1.2).
• Release the fixing bush 18 (see fig. 1.3).
• Install the holder 12 (with the sprayer 11 installed)
into the tube 13 as shown in figure 1.4.
• Install the tube 13 (with the holder 12 and the
sprayer 11 installed) into the outlet fitting 1 as shown
in figure 2.
• Disassemble in reverse order�
Assembly / disassembly / installation of detergent
spray nozzle (see fig. 3)
• Fig� 3�1 shows how to remove / install the tank of the
detergent spray nozzle 16�
• Install the detergent spray nozzle 16 into the tube 13
as shown in figure 3.2. Attention: use the detergent
spray nozzle 16 only with the tube 13. Do not install
the detergent spray nozzle 16 into the outlet fitting 1.
• Install the tube 13 (with the detergent spray nozzle 16
installed) into the outlet fitting 1 as shown in figure 3.3.
• Disassemble in reverse order�
Water connection (see fig. 4-7)
Connecting to the water supply system (see fig. 4)
• To ensure sufficient water supply, use the shortest
possible hose (minimal diameter, 13 mm, or 1/2");
if the hose is longer than 10 m, its min� diameter
shall be 19 mm (3/4")� Attention: water hose is not
supplied.
• Quick-release couplings (not supplied) shall be
installed on both ends of the hose, which will ensure
quick and reliable connection� Attention: metal hose
couplings with "Aquastop" leakage protection
system may damage the power tool. Use plastic
hose couplings instead.
• Install quick-release adapter (with valve) 14 on
the inlet fitting 10 as shown in figure 4.1. Warning:
when the power tool is connected to running water
supply, always install the quick-release adapter
(with valve) 14. Open the valve immediately before
starting the operation. When the operation is
finished, immediately close the valve.
• Connect one end of the hose to the water supply
tap, and the other one to the quick-release adapter
(with valve) 14 (see fig. 4.2).
English
27