Related Manuals for Nugsmasher ProTouch
Summary of Contents for Nugsmasher ProTouch
- Page 1 Version 1.0 NS102521 Copyright © 2021 NugSmasher. All Rights Reserved. N u g S m a s h e r p r o t o u c h...
-
Page 2: Table Of Contents
table of contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick Start Guide . -
Page 3: Introduction
Thank you for the purchase of your NugSmasher® ProTouch. We have designed this unit for the purpose of effortless rosin extraction with industry leading 7”x 10” plates and integrated touch screen allowing for the ultimate control and pressure application. When setting up your unit, please ensure your stand is suitable for the weight of the machine. -
Page 4: Quick Start Guide
quick start guide • Your release knob is packaged in foam near the heat plates and will be installed on the right side of unit towards bottom of press. • Notice the keyed end of the release valve as it slides through side of unit and can be installed easily by looking at rear of machine under manual handle sticker. - Page 5 Powering off Unit: DO NOT power off your unit by the switch! It is imperative (red circle) and display will start within 5 - 7 seconds. The NugSmasher® when powering down to use the on screen power button (green circle in ProTouch is designed with several time saving features that will allow you illustration below).
- Page 6 Do not adjust the copper bleed valves on through the unit which will slow plate right side of joystick. The new ProTouch movement and allow for fine incremental has main power switch on rear of unit pressure application.
-
Page 7: Unit Operation
It is key to do this slowly to properly build heat into your material. The entire pressing process should be between 90-120 seconds depending on your strain. Your NugSmasher® ProTouch is most capable of over pressing your material as the mistake made most with new extractors. - Page 8 NugSmasher® extraction bags, are recommended for optimal yield and clean quality rosin. Our bags are hand-made and packaged in the USA! NugSmasher® extraction bags are specifically designed to work with the weight of fresh cured flower and are labeled accordingly at: 3.5 g (1.1g-3.5g), 7 g (3.6g-7g) and 14 g (7.1g-14g). This assumes the bags are loaded (BTS) or bottle/barrel-tech style (upright so that you end up with the round coin like puck once fully pressed).
-
Page 9: Pressure System
This is the applied pressure and should be adjusted to the the extraction (Gauge PSI Reading) surface area to achieve optimum results. Surface Area Key NugSmasher® ProTouch Consistency Chart PSI to Surface Area Bag Selection PSI ON Material 1000 1250 1500 One 3.5G... - Page 10 pressure System EXTRACTION EXAMPLE: One 14g Bag Four 14g Bags Plate Pressure Plate Pressure 750 PSI 750 PSI There is only one 14g bag There are four 14g bags that has the total surface that has a total combined surface area of around 4.91in area of around 19.64in Hydraulic Fluid Pressure...
-
Page 11: Notice
The same shall also apply to the case even if NugSmasher® had been notified of the possibility of arising damages in advance. As an example, we shall not be liable for any loss of material made using this product or indirect damages caused by the product. -
Page 12: Safety
Safety • Keep away from children, pets and clothing. • Never leave the extractor on when you go to sleep or leave the area. • Never use or store flammable liquids (such as gasoline) around the extractor. The flammable vapors can flow from one part of the room to another and be ignited by an electrical spark. - Page 13 rosin made simple NS102521 Version 1.0...
Need help?
Do you have a question about the ProTouch and is the answer not in the manual?
Questions and answers