Advertisement
Powering
Trusted Identities
4. Regulatory information
SRD Model: MOD001
RF Specifications
Standard protocol
BLE 4.2
Frequency band
2400-2483.5 MHz
No of RF channels
40
RF output power
+5 dBm
Modulation
GFSK
Antenna
PCB, 0.30 dBi
Communication Regulation
The following is a list that applies:
US FCC – United States Compliance
FCC ID: SL6-MOD001
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT: Changes or modifications to this product not authorized by
HID, could void the FCC Certification and negate your authority to operate
this product.
Note: This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC rules.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This module is certified pursuant to two Part 15 rules sections(15.247).
Integrator / End Product
The user manual of the end product should include:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator and your body.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
Label of the end product:
The host product must be labeled in a visible area with the following
"Contains FCC ID: SL6-MOD001".
The end product shall bear the following 15.19 statement: This device
complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference
that may cause undesired operation.
PLT-06387, Rev. A.0
Canada Compliance
24824-MOD001
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et
(2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
Cet équipement est conforme aux limites d'exposition aux rayonnements
IC établies pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec un minimum de 20cm de distance entre la source de
rayonnement et votre corps
OEM integrator is still responsible for testing their end product for any
additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met
(for example certain laptop configurations or co-location with another
transmitter), then the IC authorization is no longer considered valid and the
IC number can not be used on the final product. In these circumstances,
the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate IC authorization.
OEM Integrator Notice
End Product Labeling
This transmitter module is authorized only for use in device where the
antenna may be installed such that 20 cm may be maintained between the
antenna and users. The final end product must be labeled in a visible area
with the following: "Contains transmitter module IC: IC: 24824-MOD001".
Contient le module d'émission IC: IC: 24824-MOD001
The Host Model Number (HMN) must be indicated at any location on the
exterior of the end product or product packaging or product literature which
shall be available with the end product or online.
This device is intended only for OEM integrators under the following
conditions:
1. The antenna must be installed such that 20cm is maintained between the
antenna and users, and
2. The transmitter module may not be co-located with any other transmitter
or antenna.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les
conditions suivantes: (Pour utilisation de dispositif module)
1. L'antenne doit être installée de telle sorte qu'une distance de 20cm est
respectée entre l'antenne et les utilisateurs, et
2. Le module émetteur peut ne pas être coïmplanté avec un autre émetteur
ou antenne.
Australia/ New Zealand Compliance
This product conforms to Australia and New Zealand Radio Requirements.
Japan
217-220435
UK Compliance
9
HID® MOD001
Install Guide
January 2022
Advertisement
