Table of Contents
Advertisement
Quick Links
Instruction Revision: C
S
(2) Table Slats with 3 holes (Aluminum Reinforced)
(2) Table Slats with 5 holes (Aluminum Reinforced)
(1) Center Table Slat with Umbrella hole (Aluminum
Reinforced)
(4) Legs: (2)Left and (2) Right
(1) Table Center Cleat with 2 holes
(2) Table End Cleats with 4 holes
READ ENTIRE INSTRUCTIONS BEFORE BEGINNING! Carefully remove contents
from box. Make sure that all parts and hardware are included.
Place All Table Slats face down with Aluminum facing up
on a flat clean surface. Use the following list for placement.
1st Slat (Far Left)= Table Slat with 3 holes #1,#6,#11
2nd Slat (Middle Left)= Table Slat with 5 holes #2,#7,#12
3rd Slat (Middle)= Center Table Slat with 3 holes #3,#8,#13
4th Slat (Middle Right)= Table Slat with 5 holes #4,#9,#14
5th Slat (Far Right)= Table Slat with 3 holes #5,#10,#15
(Right Picture)
WARRANTY QUESTIONS OR COMMENTS PLEASE CALL TOLL FREE AT 1-800-809-3114
C
EASIDE
ASUAL
(43) Traditional Picnic Table Rev. C
Box 1:
A
SSEMBLY
Step 1: Set Up
Step 2: Table Slat Placement
F
URNITURE
Parts List
(4) Seat Slats with 2 holes (Aluminum
Reinforced)
(4) Seat Cleats
(2) Angle Braces
(2) Seat Supports
I
NSTRUCTIONS
1
Hardware:
(27) 4" Carriage Bolts (5/16")
(24) 3" Carriage Bolts (5/16")
(51) Nuts
(51) Flat Washers
(51) Lock Washers
(4) 80mm Lags
Tools Required:
Allen key
1/2" Socket
Hammer
Box 2:
Advertisement
Table of Contents
Related Manuals for SEASIDE CASUAL FURNITURE Traditional Picnic Table 043
Summary of Contents for SEASIDE CASUAL FURNITURE Traditional Picnic Table 043
- Page 1 Instruction Revision: C EASIDE ASUAL URNITURE (43) Traditional Picnic Table Rev. C Hardware: (27) 4” Carriage Bolts (5/16”) (24) 3” Carriage Bolts (5/16”) (51) Nuts (51) Flat Washers (51) Lock Washers (4) 80mm Lags Tools Required: Allen key 1/2” Socket Hammer Parts List Box 1:...
- Page 2 Step 3: Carriage Bolt Placement Insert (19) 4” Carriage Bolts (5/16”) into all Table Slat End and Center Holes. Tap bolts with a hammer to set square into the End and Center Holes (Right picture) Step 4: Table End & Center Cleats Attachment Align End and Center Cleats onto Carriage Bolts by tapping them into place with a ham- mer.
- Page 3 Step 7: Angle Brace Attachment Place (2) Angle Braces along Seat Supports to the Table Center Cleat while aligning pre-drilled holes. Attach using (4) 80mm Lags (Socket drive). (Right picture) Step 8: Flip Table to upright position Flip Table to upright position on its legs. This will require two people. Step 9: Seat Cleats Attachment Place (4) Seat Cleats along inside of Seat Supports, while aligning pre-drilled holes (AS SHOWN).
Need help?
Do you have a question about the Traditional Picnic Table 043 and is the answer not in the manual?
Questions and answers