Crane Barnes 3SE-DS Series Installation And Operation Manual
Submersible sewage ejector
Hide thumbs
Also See for Barnes 3SE-DS Series:
- Installation and operation manual (21 pages) ,
- Installation and operation manual (32 pages) ,
- Installation and operation manual (20 pages)
Table of Contents
Advertisement
Quick Links
INSTALLATION and OPERATION MANUAL
Series: 3SE-DS, 3HP
1750RPM, 60Hz.
(Double Seal)
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notification.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
BARNES
BARNES
Submersible Sewage Ejector
83 West Drive, Brampton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
®
Form No. 088743-Rev. S
Advertisement
Table of Contents
Related Manuals for Crane Barnes 3SE-DS Series
Summary of Contents for Crane Barnes 3SE-DS Series
- Page 1 Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur. As such Crane Pumps & Systems reserves the right to change product without prior written notification. A Crane Co. Company...
-
Page 2: Table Of Contents
PRESSURE GAUGE KIT (see parts list) Other brand and product names are trademarks or registered trademarks of their respective holders. ® Barnes is a registered trademark of Crane Pumps & Systems, Inc 1996, 1997, 1998, 1999, 2001, 2002, 3/06, 9/06, 2/07... -
Page 3: Safety First
WARNING! - DO NOT pump hazardous materials IMPORTANT! - Crane Pumps & Systems, Inc. is not (flammable, caustic, etc.) unless the pump is specifically responsible for losses, injury, or death resulting from a designed and designated to handle them. -
Page 4: Pump Specifications
SECTION: A - PUMP SPECIFICATIONS: 1750RPM DISCHARGE ....3” NPT, Vertical UPPER BEARING: LIQUID TEMPERATURE . 104°F (40°C) Continuous Design ..Single Row, Ball, Oil Lubricated MOTOR HOUSING ..Cast Iron ASTM A-48, Class 30 Load ..... Radial VOLUTE ......Cast Iron ASTM A-48, Class 30 LOWER BEARING: SEAL PLATE .... -
Page 5: General Information
For the location of the nearest Barnes Service Center, check with grout and/or shims. Install the intermediate support your Barnes representative or Crane Pumps & Systems, Inc., brackets, if required. Make sure the rails are in a true vertical Service Department in Piqua, Ohio, telephone (937) 778-8947 position so the pump will clear the access opening and or Crane Pumps &... - Page 6 C-4) Electrical Connections: NOTE: Single phase pumps can be orederd with an optional C-4.1) Power & Control Cords: Thermal Sensor as well as the standard in winding overload The cord assembly mounted to the pump must not be modified protection. in any way except for shortening to a specific application.
-
Page 7: Start-Up Operation
SECTION: D START-UP OPERATION SECTION F: SERVICE AND REPAIR D-1) Check Voltage and Phase: NOTE: All item numbers in ( ) refer to Figures 9 & 10, Before operating pump, compare the voltage and phase 3450RPM and Figures 11 & 12 , 1750RPM. information stamped on the pump identification plate to the available power. - Page 8 F-1.4) Pressure Test: F-2) Impeller and Volute Service: Motor Housing - Before checking the pump for leaks around F-2.1) Disassembly and Inspection: the shaft seal, square rings, and cord inlet, the oil level should To clean out volute (25), disconnect power, remove hex nuts be full as described in section F-1.3.
- Page 9 Position motor housing and stator into pilot, aligning holes Important ! - ALL parts must be clean before reassembly. in bearing bracket (20). Apply thread locking compound on motor bolts and tighten. Torque motor bolts to 17 ft. lbs. Place all motor leads above the motor.
- Page 10 F-4) Shaft Seal and Diaphragm Service: Important ! - Handle seal parts with extreme care. DO NOT scratch or mar lapped surfaces. F-4.1) Disassembly and Inspection: Diaphragm - To examine or replace the diaphragm (31) or shaft seal (38), remove impeller (27) as outlined in paragraph F-2.1.
- Page 11 FIGURE 6 FIGURE 5 Seal - Clean and oil seal cavities in bearing bracket (20) Motor & Seal Plate and seal plate (24). Lightly oil (DO NOT use grease) outer Rotating Member (38D) surface of inboard stationary member (38E) and outboard Stationary stationary member (38A).
-
Page 12: Replacement Parts
SECTION: G REPLACEMENT PARTS G-1 ORDERING REPLACEMENT PARTS: When ordering replacement parts, ALWAYS furnish the following information: 1. Pump serial number and date code. (Paragraph G-4) 2. Pump model number. (Paragraph G-3) 3. Pump part number. (Paragraph G-2) 4. Part description. 5. -
Page 13: Trouble Shooting
TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... - Page 14 3SE-DS 1750RPM FIGURE 11...
- Page 15 3SE-DS 1750RPM FIGURE 12...
- Page 16 PARTS LIST - 1750RPM Seal Repair Kits Double Seal..P/N - 130178 (†) 10, 31, 36, 38 Service Kits Double Seal..P/N - 130174 (♦) 10, 11, 16, 28, 29, 30, 31, 32, 33, 36, 38, 39 Seal Tool Kit....P/N-085736 Pressure Gauge Kit...P/N-085343 ITEM PART NO.
- Page 17 057882 ♦ Retaining Ring 003217 ♦ Pipe Plug (Replaces Item 18) 022873 †♦ Diaphragm 059186 ♦ Shaft Key 3/16 Sq x 1” Lg Stainless 038132 ♦ Hex Nut 5/8-18 Stainless 11-32-1 Soc. Hd. Cap Screw 1/4-20 x 1” Lg Stainless 033730 †♦...
- Page 18 Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”. CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR. Products Returned Must Be Cleaned, Sanitized, Or Decontaminated As Necessary Prior To Shipment, To Insure That Employees Will Not Be Exposed To Health Hazards In Handling Said Material.
Need help?
Do you have a question about the Barnes 3SE-DS Series and is the answer not in the manual?
Questions and answers