Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PCB Piezotronics IMI SENSORS 699A05
Summary of Contents for PCB Piezotronics IMI SENSORS 699A05
- Page 1 Model 699A05 4-20 mA Loop Calibrator Installation and Operating Manual For assistance with the operation of this product, contact PCB Piezotronics, Inc. Toll-free: 800-959-4464 24-hour SensorLine: 716-684-0001 Fax: 716-684-3823 E-mail: imi@pcb.com Web: www.imi-sensors.com...
-
Page 2: Repair And Maintenance
Assistance is needed to safely operate equipment PCB Piezotronics is an ISO-9001 certified company whose Damage is visible or suspected calibration services are accredited by A2LA to ISO/IEC Equipment fails or malfunctions 17025, with full traceability to SI through N.I.S.T. - Page 3 CAUTION Refers to hazards that could damage the instrument. NOTE Indicates tips, recommendations and important information. The notes simplify processes and contain additional information on particular operating steps. The following symbols may be found on the equipment described in this manual: This symbol on the unit indicates that high voltage may be present.
- Page 4 PCB工业监视和测量设备 - 中国RoHS2公布表 PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table 有害物质 镉 汞 铅 (Pb) 六价铬 (Cr(VI)) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 部件名称 (Hg) (Cd) 住房 PCB板 电气连接器 压电晶体 环氧 铁氟龙 电子 厚膜基板 电线 电缆 塑料 焊接...
- Page 5 Component Name Hazardous Substances Lead (Pb) Mercury (Hg) Cadmium (Cd) Chromium VI Polybrominated Polybrominated Compounds Biphenyls (PBB) Diphenyl Ethers (Cr(VI)) (PBDE) Housing PCB Board Electrical Connectors Piezoelectric Crystals Epoxy Teflon Electronics Thick Film Substrate Wires Cables Plastic Solder Copper Alloy/Brass This table is prepared in accordance with the provisions of SJ/T 11364.
-
Page 6: Ez-Dial™ Knob
Model 699A05 4-20 Milliamp Loop Calibrator Operating Instructions Basic Keypad Operations EZ-Check™ Switch SOURCE/OFF/READ Switch Slide the SOURCE/OFF/READ Switch to SOURCE to SOURCE mode: Slide the switch to select from Hi and low range pre- output a mA signal and to do 2 - wire transmitter set values and the mid ranger (Dial) is selectable. -
Page 7: Ez-Check™ Switch
Model 699A05 Operating Instructions EZ-Check™ Switch The EZ-Check™ switch has three positions -- high, dial, and low. Its position is shown at the left edge of the display with “HI” and “LO” indicators. Neither indicator indicates the middle position. Use of the EZ-Check™ switch depends on mode. Source Modes: Slide the EZ-Check™... -
Page 8: Read Mode
Model 699A05 Operating Instructions Power and Measure Transmitter Mode Receiv er Transmitter Input + IN - REF +OUT- (Sensor) ocess Signal) mulat d Input) Typical 2-Wire Transmitter Pow er Supply 0 to 0 VDC The Model 699A05 supplies 15Volts or 24 Volts to the transmitter and displays the output in mA or % on the Model 699A05 display. In read mode press the EZ-Dial™... -
Page 9: Specifications
Model 699A05 Operating Instructions Specifications General Specifications: (Unless otherwise indicated all specifications are rated from a nominal 23 °C, 70 % RH for 1 year from calibration) Operating Temperature Range -20 to 60 °C (-5 to 140 °F) Storage Temperature Range -30 to 60 °C (-22 to 140 °F) Relative Humidity Range 10 % ≤RH ≤90 % (0 to 35 °C), Non-condensing...
Need help?
Do you have a question about the IMI SENSORS 699A05 and is the answer not in the manual?
Questions and answers