Advertisement
Quick Links
Installation Instructions for
This installation is not fo the electrically or mechanically
challenged! Use th
uncomfortable with anything about this, please refer the
!
installation to an AEM trained tuning shop or call 800-423-0046
for technical assistance. You should also visit the AEM
Performance Electronics Forum at http://www.aempower.com
NOTE: AEM holds no responsibility for any engine damage tha
r
esults from the misuse of this product!
This product is legal in California for racing vehicles onl
30-4350
AEM Tru Boost
Boost Controller Gauge
WARNING:
is gauge with
never be used on public highways.
ADVANCED ENGINE MANAGEMENT INC.
th
2205 126
Street Unit A, Hawthorne, CA. 90250
Phone: (310) 484-2322 Fax: (310) 484-0152
http://www.aempower.com
Instruction Part Number: 10-4350 Rev 090506
© 2006 Advanced Engine Management, Inc.
Page 1
r
EXTREME
caution! If you are
y and should
t
Advertisement
Related Manuals for AEM 30-4350
Summary of Contents for AEM 30-4350
- Page 1 EXTREME caution! If you are uncomfortable with anything about this, please refer the installation to an AEM trained tuning shop or call 800-423-0046 for technical assistance. You should also visit the AEM Performance Electronics Forum at http://www.aempower.com NOTE: AEM holds no responsibility for any engine damage tha...
- Page 2 LED digital readout with 24 sweeping multi color LED’s, two programming uttons, and an on-board pressure sensor. The Tru Boost kit contains all necessary components, including an AEM high performance boost control solenoid, to install and use the Tru Boost.
- Page 3 Installing the Gauge The AEM Tru Boost boost controller gauge requires a standard 2 1/16” (52MM) ounting hole and can be mounted in a flat panel or most standard gauge pods. The included cable contains two wire bundles and a 5-pin connector. The 5-pin connector connec ts to a mating 5-pin connector on the back of the gauge.
- Page 4 Scramble Boost Connection (Optional) Scramble boost is activated when the orange wire is grounded. Connect the range wire to ground through a switch as shown in Figure 5. Switch ORANGE (SCRAMBLE BOOST) Ground Figure 5. Scramble Boost Connection Warning Light Connection (Optional) The Tru Boost w ill ground the gray wire when the alarm is activated.
- Page 5 50 psig when using the optiona l external sensor kit. The 30-4351 sensor kit comes with an AEM 75psia senso and a harness to connect the sensor to the Tru Boost. See Figure 9. Plug the single row 3-pin connector into the mating connector on the back of the gauge.
- Page 6 larm: (ALA - 30) Set the boos t pressure at which the alarm will activate. When the alarm is activated, the LED lights flash yellow and the warning light output (grey wire) is pu lled to ground. pring Pressure: (SPr – 2.00) Enter the waste gate sprin g pressure(3psi less then your spring).
- Page 7 Page 7...
- Page 8 Using the Tru Boost The Tru Boost has 3 running modes. In all modes, for manifold pressures less than 0 psig, the sweeping LED’s remain off, the gauge displays pressure in units of in-hg, and the displayed values are negative. In mode A, the gauge will output the duty cycle selected for boost setting A.
- Page 9 Changing the gauge configuration The AEM Tru Boost comes configured with the black bezel, black pin guide, and the black faceplate. However, a silver bezel, a silver pin guide, and a white faceplate are also included in the gauge kit. To change the faceplate, pin guide, or bezel, orient the gauge so you are looking at the faceplate.
-
Page 10: Aem Electronics Warranty
AEM that the product failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of the AEM part. In no event shall this warranty exceed the original purchase price of the AEM part nor shall AEM be responsible for special, incidental or consequential damages or cost incurred due to the failure of this product.
Need help?
Do you have a question about the 30-4350 and is the answer not in the manual?
Questions and answers