Trane ProSpace PTEF Installation, Operation And Maintenance Manual page 26

O O p p e e r r a a t t i i o o n n
•
Changing Batteries in the Remote Control
The remote requires two (2) AAA, 1.5V batteries.
1. From the back side of the remote, gently press down on the battery cover and slide it towards
2. Remove the old batteries from the battery compartment.
3. Insert two (2) new batteries into the battery compartment. Ensure the batteries poles match
4. Slide the battery cover back onto the remote until the tab clicks.
B B E E S S T T P P R R A A C C T T I I C C E E : :
Check your local city/state for proper recycling procedures. A battery is an electrochemical device
with the ability to convert chemical energy to electrical energy to provide power to electronic
devices. Batteries contain heavy metals such as mercury, lead, cadmium, and nickel, which can
contaminate the environment when batteries are improperly disposed of. When incinerated,
certain metals might be released into the air or can concentrate in the ash produced by the
combustion process. Batteries may produce the following potential problems or hazards:
•
•
•
•
26
setting and the T-ON or H characters do not display. When the temperature display becomes
constant, press this key again to display the remaining set time. The time values, T-ON and H,
display constantly for 2 seconds. After 2 seconds, the preset temperature displays. Within
these 2 seconds, press this key again to CANCEL the AUTO SWITCH ON and send the
message. Pressing this key in SWITCH ON state allows the time to be set to AUTO SWITCH
OFF . Press ON/OFF key to switch on the unit and CANCEL the AUTO SWITCH ON state.
N N o o t t e e : : The +/- buttons are used to increase/decrease value settings for either time or
temperature. Refer to the sub-sections below about how to use the +/- buttons to set
temperature values.
– + + B B u u t t t t o o n n ; press this button to set increased temperature values when unit is ON.
Continuously press and hold this button for more than 2 seconds until °F (°C) displays. In
AUTO Mode, the temperature can not be set up, but this button can send the signal.
Temperature ranges are between 61°F and 86°F (16°C and 30°C).
N N o o t t e e : : To switch between Fahrenheit and Celsius, press and hold the - - a a n n d d M M O O D D E E keys
simultaneously while in S S W W I I T T C C H H O O F F F F state.
– - - B B u u t t t t o o n n ; .press this button to set decreased temperature values when unit is ON.
Continuously press and hold this button for two seconds to decrease the temperature
value. The temperature adjustment is unavailable in AUTO Mode, but this button can send
the signal.
L L O O C C K K ; to LOCK and UNLOCK (default) the keypad, press and hold the - - o o r r + + a a n n d d M M O O D D E E keys
simultaneously while in either S S W W I I T T C C H H O O N N S S W W I I T T C C H H O O F F F F states. The unit show the LOCK
icon when in LOCK Mode, in which case, the lock icon flashes three (3) times upon operation
of any key. The LOCK icon does not display when the unit is in UNLOCK Mode.
the bottom of the unit.
the polarity when inserting them into the battery compartment: + to + and - to -.
N N o o t t e e : : Only use the recommended battery type. If the remote has not been used for an
extended period of time, check the expiration date on the batteries or check for battery
leakage.
Pollute the lakes and streams as the metals vaporize into the air when burned
Contribute to heavy metals that potentially may leach from solid waste landfills.
Expose the environment and water to lead and acid.
Contain strong corrosive acids. May cause burns or danger to eyes and skin.
PTAC-SVX002A-EN