Table of Contents
Advertisement
INSTALLATION
The VCR requires connections to both UHF and VHF antennas and the TV set.
VHF Antenna
UHF Antenna
®
®
!
I
300ohm to 75
F Connector
(supplied)
ohm Transformer
(supplied)
(;J
G)
Connect your UHF antenna to the rear of the unit as shown.
®
If you use 300 ohm twin-lead (flat) cable from your VHF
antenna, use the 300 ohm-75 ohm transformer as shown to
connect to the VHF Input of the unit.
@)
If you use 75 ohm coaxial cable from your VHF antenna,
connect it to the rear of the unit as shown.
If your 75 ohm coaxial cable does not use an "F" type
connector, you can install one yourself by using the included
"F" connector.
How to attach a male "F" connector to RG59/U type
coaxial cable with braided copper shield.
1. Prepare the end of coaxial cable as shown.
5/16" 5/16"
(8 mm) (8 mm)
i-------1-----(smm)
� U
LI
�B r aided copp
Poly
Solid copper conductor
The
length
of the
polyethylene dielectric and braid shield should be
measured and cut carefully.
2. Fold back the copper braid shield over the outer jacket,
next, trim off the shield close to outer jacket.
�
3. Slide the crimping ring supplied with "F" connector over
the cable and place connector on cable inserting the
mandrel (tapered end) of "F" connector between the
G)
3116"
Vinyl jack
t
e
r shi
ld
thyl
n
di
lectric
e
e
e
e
e
e
solid copper conductor,
@
300 ohm Twin-Lead Cable (supplied)
®
Coaxial Cable with one-touch
type F Connector (supplied)
®
[I
1111111111111111111
1111111111111111111
1111111111111111111
1111111111111111111
1111111111111111111
@
@
0
braid shield and the dielectric material of coaxial cable,
� �
forcing it in until the braid is touching the back piece of
connector.
LL
L
Mandr
l (tap
B a ck pi
c
e
Coupling nut
e
e
�
Move the crimping ring up to the back piece of the
connector and crimp the ring securely with pliers.
•The bare solid copper conductor extend at least 1 /8"
(3.17 mm) beyond front of connector.
•After crimping the ring make sure that the connector
cannot be pulled out of the coaxial cable.
©
Use the supplied 300 ohm twin-lead cable to connect the unit
to UHF Input of your TV.
®
Use the supplied coaxial cable with one-touch type F
connector to connect the unit to VHF Input of your TV.
®
If your TV does not have a 75 ohm VHF Input, use the VHF
matching box 75 ohm-300 ohm transformer.
(J)
Plug the unit into an AC 120 V 60 Hz electrical outlet.
-9-
TV Set
VHF Matching Box 75 ohm-300 ohm
Transformer (supplied)
l@J
[1]
-@
@O
V
..
°'*;;;;,
L
L Crimping ring
Crimping ring
L
red
nd)
_
Ins
rt until b raid touch
dg
o
ack piec
e
e
f b
e
�
�
e e
e
O
L
x i : ca
c oa
L
l
Ring (crimp
d ring)
B a ck pi
c
e
Coupling nut
e
e
Solid copp
r conductor
e
_
s
e
e
Advertisement
Table of Contents
