Cleaning And Maintenance; Delivery Set - Maxwell MW-3400 Manual Instruction

ENGLISH
Cleaning the carpets
•
Install the carpet glider (14) on top of the mop noz-
zle (10) with the cloth (13) attached. To do this, first
install the front part of the mop nozzle (10) into the
glider (14), then install the rear part and press until the
glider is installed to its place.
•
The glider (14) provides the easy gliding of the mop
nozzle (10) along the carpets without the cloth (13)
slipping up.
•
Plug the unit into the mains and set the power
switch (7) to «I» - the green light on the power/no
water indicator (8) will turn on.
•
The unit heats up and will start generating steam in
approximately 30 seconds.
•
To keep the power cord out of the way during clean-
ing, pass it through the upper hook (2).
RECOMMENDATIONS ON USING
•
Before cleaning the floor, it is recommended to sweep
or vacuum it to remove dust and dirt particles.
•
When washing the floor, move the unit in an even back
and forth motion, pushing it away from you and pull-
ing it back. Move backwards to avoid stepping on the
already washed floor.
•
The microfiber cloth (13) collects water when wash-
ing the floor. However, depending on the character-
istics of the floor surface and the set steam intensity,
some moisture may remain on the floor. In this case,
it is recommended to let the floor dry naturally. Drying
can be accelerated by using a fan directed to the
desired area.
•
After you finish cleaning, remove the cloth (13) from
the mop nozzle (10). Then the floor under the mop will
not get soaked from a damp cloth.
•
You can clean the carpets with the mop nozzle (10)
with installed glider (14). To freshen the carpet, try to
do the following: dilute carpet shampoo with water in
a 1:1 ratio. Spray the resulting solution on the carpet
and leave it for 2 hours. When the 2 hours expire, clean
the carpet with the steam mop. The carpet will be wet
after this procedure, so you'll have to dry it.
•
It is recommended to fully change the water in the tank
(9) from time to time to avoid stagnation of water and
the appearance of an extraneous smell.
•
The water hardness level is different for every region.
Water can contain hardness salts and other dissolved
minerals. Water evaporates in the boiler and the resi-
due remains.
•
If water is soft and does not contain a lot of salts, the
scale flakes will from time to time fall off the boiler
walls and go out with the steam. If the water contains
a lot of salts, including the hardness salts, then min-
eral deposits will accumulate in the boiler in a signifi-
cant amount. It will hinder steam generation and may
cause damage. Scale flakes can clog valves and con-
nections. Therefore, it is recommended to use demin-
eralized or distilled water to reduce limescale and salt
deposits.
•
Regular jug filters do not remove minerals and salts
from water. Special demineralizing filters are used for
this purpose.
•
If you want to use bottled drinking water, find out its
total mineralization (usually indicated on the label) and
compare it with indicators for tap water (they can be
found on the water supply company's website or by
the Internet search). Typically, bottled water salinity is
100-400 mg / l. It may turn out that the water from the
tap has salinity several times lower, so that the use of
bottled water will increase the formation of scale.
Attention! Scale deposits and salts can be removed
from the boiler only in the service center. This procedure
is not covered by warranty and requires payment.

CLEANING AND MAINTENANCE

•
Switch the unit off and unplug it.
•
Tilt the mop and pour the remaining water out of the
water tank (9) and into a suitable container.
•
Wipe the steam mop body with a damp cloth.
•
Let the cloth (13) cool down for several minutes before
removing it from the mop nozzle (10).
•
You can wash the microfiber (13) cloth in a washing
machine, using a delicate cycle and at temperature
not exceeding 60°C.
•
Do not use bleachers, fabric softeners or rinses, so
the cloth can absorb dirt. You can dry the cloth in a
dryer.
•
For hand wash, use a mild detergent and dry the cloth
in horizontal position.
Cleaning the water tank
•
Periodically wash the water tank (9). Avoid stagnation
of water in the tank.
•
To remove lime deposits that build up inside the water
tank, add one or two tablespoons of white vinegar into
the full water tank, tightly close the water tank feed-
ing chute (5) and shake its contents, then tilt the mop
and pour the solution out and into a suitable container.
Wash the tank with clean water in a similar fashion.
Note: If you always use distilled water, you don't need to
clean the water tank.
Attention! Perform a test cleaning of a suitable isolated
area after each descaling to make sure that no scale or
dirt is left inside the unit.
STORAGE
Note: After usage, tilt the mop backwards and pour the
remaining water out into a suitable container.
•
Switch the unit off and unplug it.
•
Follow the requirements of the "Cleaning and care"
section.
•
Wind the power cord on the special cord storage
hooks (2, 4).
•
Place the mop vertically.
Note: The mop can be conveniently stored in a vertical
standby position.
•
Keep the steam supply away from children in a dry
and cool place.

DELIVERY SET

Steam mop – 1 pc.
Carpet glider – 1 pc.
Microfiber pad – 1 pc.
Funnel – 1 pc.
Beaker – 1 pc.
Instruction manual – 1 pc.
Warranty certificate – 1 pc.
10