Before The First Use - Maxwell MW-3400 Manual Instruction

•
Avoid getting burns by hot steam.
•
Unplug the unit after usage or before cleaning.
•
When unplugging the unit hold the power plug and
remove it from the mains socket, do not pull the
power cord – this can lead to its damage and cause
short circuit.
•
The unit is not intended for usage by children.
•
Do not leave children unattended to avoid them using
the unit as a toy.
•
Do not allow children to touch the operating surface,
unit body, power cord or power plug during operation
of the unit.
•
Be especially careful if children or disabled persons are
near the operating unit.
•
During the unit operation and breaks between opera-
tion cycles, place the unit out of reach of children.
•
The unit is not intended to be used by people with phys-
ical, sensory or mental disabilities (including children)
or by persons lacking experience or knowledge if they
are not under supervision of a person who is respon-
sible for their safety or if they are not instructed by this
person on the usage of the unit.
•
For child safety reasons do not leave polyethylene bags
used as packaging unattended.
Attention! Do not allow children to play with polyethylene
bags or packaging film. Danger of suffocation!
•
From time to time check the power cord integrity.
•
If the power cord is damaged, it should be replaced
by the manufacturer, a maintenance service or similar
qualified personnel to avoid danger.
•
Do not use the unit if the power cord or the power plug
is damaged, if the unit works improperly and after it
was dropped.
•
Do not repair the unit by yourself. Do not disassemble
the unit by yourself, if any malfunction is detected or
after it was dropped, unplug the unit and apply to any
authorized service center at the contact addresses
given in the warranty certificate and on the website
www.maxwell-products.ru.
•
To avoid damages, transport the unit in the original
package only.
•
Keep the unit in a dry cool place out of reach of children
and disabled persons.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY.
ITS COMMERCIAL USE AND USE IN PRODUCTION AND
WORKING AREAS ARE PROHIBITED.

BEFORE THE FIRST USE

After unit transportation or storage at low temper-
ature keep it for at least three hours at room tem-
perature.
•
Unpack the unit and remove any packaging materials
and advertising stickers.
•
Keep the original package.
•
Read the safety measures and operating recommen-
dations.
•
Check the delivery set.
•
Examine the unit for damages; if the unit is damaged,
do not plug it into the mains.
•
Make sure that the indicated specifications of the
power supply voltage of the unit correspond to the
specifications of your mains.
•
To remove dust clean the unit with a slightly damp cloth,
and then wipe it dry.
ASSEMBLING THE STEAM MOP
Note: Each steam mop passes 100% testing at the factory
to guarantee the working ability and safety of the product.
When assembling a new steam mop for the first time you
can find some water remaining inside the unit. This is not
a defect.
•
Remove the unit from the packaging making sure the
product is not damaged and that all parts are included
in the package.
•
Insert the extension pipe (3) into the upper part of the
steam mop body so that it makes a clicking sound, hav-
ing aligned the lock (6) with the inlet in advance (fig. 1).
To extract the extension pipe (3), press the lock (6) and
pull it out of the body.
USING THE STEAM MOP
•
Attach the microfiber pad (13) to the mop attachment
(10) (fig. 2), tighten the string and fixate it with the
clamp. Tuck the remainder of the string under the pad.
Important: Never use the steam mop without the microfi-
ber pad (13) attached to the mop attachment (10) or with
no water in the water tank (9).
Attention! Avoid dropping of the steam mop on the floor.
Hitting the floor can damage the inner parts of the appli-
ance and crack the mop handle.
Be sure to completely unwind the power cord before using
the unit.
The upper hook rotates (2) 180° for better power cord ac-
cessibility. Pull the hook out before rotating it.
Warning! Do not leave the unit unattended during use.
Filling the water tank with water
•
Position the steam mop vertically.
•
Insert the funnel (11) into the feeding chute (5).
•
Pour clean water into the water tank (9), using the
beaker (12), but no more than 300 ml (fig. 3). You can
determine the water level through the see-through win-
dow of the water tank.
•
Remove the funnel once the water tank is full.
Should the water tank deplete while the steam mop is in use,
switch the unit off by setting the power switch (7) to «O», un-
plug the unit from the mains, and fill the water tank (9) with
clean water, according to the above directions.
Washing and disinfecting the floor
Warning: While using the steam mop, keep it at a 45° an-
gle or less to avoid spilling the water out of the water tank.
•
Plug the unit into the mains and set the power
switch (7) to «I» - the green light on the power/no water
indicator (8) will turn on.
•
The unit will warm up and start releasing steam in about
30 seconds.
•
To keep the power cord out of the way during cleaning,
pass it over the upper hook (2).
Low water level protection
Should the water tank (9) deplete, the pump will automati-
cally stop working, and the red light on the power/no water
indicator (8) will turn on. The pump will resume operation
after you fill the the water tank with water.
9
ENGLISH