Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Eastwood 33913
Summary of Contents for Eastwood 33913
- Page 1 Item #33913 2 TON ENGINE CRANE INSTRUCTIONS...
-
Page 2: Specifications
The EASTWOOD 2 TON ENGINE CRANE features robust, heavy-duty construction and oversized components to handle frequent shop demands as well as occasional hobbyist use. Steel, ball bearing swivel casters and an 8-Ton hydraulic cylinder will support up to a total loaded weight of 2 tons [4000lb/1814 kg.] yet is completely portable for lifting and moving engines, transmissions, pickup beds and other concentrated heavy loads around vehicles and shop areas. - Page 3 (3) M16 x 2.00 x 100mm Shoulder Bolts (1) M16 x 2.00 x 90mm Shoulder Bolt (2) M16 x 2.00 x 85mm Shoulder Bolts (7) M16 Washers (7) M16 x 2.00 Nuts (4) Cotter Pins To order parts and supplies: 800.343.9353 >> eastwood.com...
-
Page 4: Safety Information
Failure to ensure proper footing can quickly result in a fall which could inflict serious personal injury or property damage. PINCH/CRUSH HAZARD! • This Engine Crane has moveable components that can crush and pinch. Keep fingers and hands away from pinch points when operat- ing. Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com... -
Page 5: Assembly Preparation
ASSEMBLY PREPARATION INJURY HAZARDS! The Eastwood 2 Ton Engine Crane consists of heavy metal components (173 lbs. [78.5 kg.] assembled weight) which can cause potentially serious injuries if allowed to drop. Avoid pinching hands while handling parts during assembly. • Obtaining the assistance of a helper during assembly is necessary. DO NOT attempt to construct this Engine Crane without assistance! •... - Page 6 TIGHTEN POST [G] AND BRACE [H] BOLTS 1. Once the Post [G] and Braces [H] are in acceptable alignment with the Base [A], all the bolts may be tightened securely using two 22mm or two 24mm wrenches (not included). Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com...
- Page 7 2. Slide the M16 x 110mm Shoulder Bolt through the holes in the “U” of the Post [G] and the end of the Lifting Boom [K], add an M16 Washer, thread on an M16 Nut then tighten securely with two M24 wrenches (not included). To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 8 Lifting Boom Extension [L] and the open link at the end of the Chain and Hook [M], thread on an M14 Nut, then secure using two 22mm wrenches (not included) (FIG 12). FIG. 12 FIG. 12 Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com...
-
Page 9: Folding For Storage
DO NOT store it in or expose it to a damp or wet environment. • Occasionally inspect all components for potential damage and proper alignment. Check all hardware for tightness • DO NOT use if damage is discovered. To order parts and supplies: 800.343.9353 >> eastwood.com... - Page 10 • Fill to full oil level using a small funnel (full oil level is even with the bottom of the fill hole). • Use only a high-quality hydraulic jack oil. The use of any other type of oil can seriously damage the Hydraulic Cylinder seals. • Replace Rubber Plug in Hydraulic Cylinder. Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com...
-
Page 11: Troubleshooting
Low Hydraulic Fluid level • Use only a high-quality hydraulic jack oil. The use of any other type of oil can seriously damage the jack pump seals. To order parts and supplies: 800.343.9353 >> eastwood.com... -
Page 12: Additional Items
If you have any questions about the use of this product, please contact The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: tech@eastwood.com PDF version of this manual is available at eastwood.com The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA 800.343.9353 eastwood.com © Copyright 2020 Eastwood Automotive Group LLC 12/20...