Sharp SX80J9 Service Manual page 4

60Hz ADJUST mode SPECIAL PICTURE mode
V-AMP 60Hz (V-AMP6)
BS DET SRT POINT (LEVEL)
V-LINE 60Hz(V-LIN6)
8 MHz f RESPONCE (RS)
S-CORRECT 60Hz(V-SCOR6)
V-PHASE 60Hz(V-PHS6)
H-PHASE 60Hz(H-PHS6) NICAM ERROR AUTO (N-AMIDIS)
H-SIZE 60Hz (V-SIZE6) V-ENHANCEMENT LEVEL (V-ENH)
In the direction of allow : CH DOWN Key
COLOUR BANDPASS FILTR (CBPF)
In the opposite direction : CH UP Key
1 LINE DOT IMPROVEMENT (LD)
PIP ADJUST mode
H-POSITION (H-POS)
V-POSITION (V-POS) H/V FRAME WIDTH (FRM)
PIP SUB TINT (PIP-TINT) FRAME COLOUR (UFC)
SUB V-PULSE DELAY (VSIDLY) FRAME LUMINANCE (YFC)
PLL TIME CONSTANT (PLLTC)
SUB H-PULSE DELAY 50Hz (HSIDLY5)
SUB H-PULSE DELAY 60Hz (HSIDLY6)
Y-DELAY NTSC (YDLYN)
MAIN V-PULSE DELAY (VSPDLY)
Y-DELAY PAL (YDLYP)
SELECT PHASE (SELDLY)
In the direction of allow : CH DOWN Key
In the opposite direction : CH UP Key
00:10 IRE ~ 11:40 IRE BS
00:28 IRE ~ 11:7 IRE SRT
MIN MAX
0 ~ 7
MIN MAX
SRT TRAC (RTC)
0 ~ 7
ON/OFF
V/C/J BS (BS)
0 / 1
ON/OFF
0 / 1
MIN MAX
0 ~ 7
ON/OFF
0 / 1
ON/OFF
0 / 1
ON/OFF
0 / 1
CORING (CORING)
In the direction of allow : CH DOWN Key
In the opposite direction : CH UP Key
NICAM mode
IGR LEVEL (IGR-LVL)
IGR STEREO (IGR ST)
NICAM ERR-MAX (N-ERR MAX)
NICAM ERR-MIN (N-ERR MIN)
NICAM AMDIS (N-AMDIS)
4-1
(2) * In going to the service mode, read the data at addresses 00H thru 03H on the EEPROM. If the data is different
from the one below, initialize the EEPROM as follows.
00H:50H 01H:80H
[Adjusting items]
No. Setting item On-screen display
0 SERVICE MODE
1 CUT OFF ADJ. CUT OFF BKGD
2 V-AMPLITUDE (50Hz) ADJ. V-AMP5
3 V-LINEARITY (50Hz) ADJ. V-LIN5
4 V-S CORRECTION (50Hz) ADJ. V-S COR5
5 V-PHASE (50Hz) ADJ. V-PHS5
6 H-PHASE (50Hz) ADJ. H-PHS5
7 H-SIZE (50Hz) ADJ. H-SIZE5
8 EW-PARABOLA ADJ. E/W PAR
9 V-BIAS V-VIAS
10 V-∫CORRECTION V-∫COR
11 EW-CORNER ADJ. E/W COR
12 TRAPEZIUM TRAPE
13 V-COMPENSATION V-COM
14 H-COMPENSATION H-COM
15 BELL FILTER ADJ. SCM BELL
16 SECAM R-Y ADJ. SCM R-Y
17 SECAM B-Y ADJ. SCM B-Y
18 SECAM GATE PULSE ADJ. SCM GP
19 SECAM CHROMA ATT SCM ATT
20 SECAM ID SETTING SCM ID
21 FLESH COLOUR SETTING FLESH
22 SRT MODE SETTING SRT-MD
23 WHITE PEEK DETECT LEVEL WPDL
24 WHITE PEEK DETECT CURRENT WPDC
25 HI-BRIGHT COLOUR SETTING HIBRT
26 Y-γ ADJ. Y-GMMA
27 COLOUR-γ ADJ. C-GMMA
28 COLOUR DETAIL SETTING CDE
29 GP-PHASE ADJ. GP-PHS
30 R-Y PHASE ADJ. RY-PHS
31 R-Y PHASE ADJ. (NTSC) RY-PHSNT
32 R-Y GAIN ADJ. RY-GAIN
33 G-Y GAIN ADJ. GY-GAIN
34 P/N ID SENSITIVITY SETTING PN-ID
35 Y DELAY ADJ. Y-DLY
36 VM-PHASE ADJ. VM-PHS
37 S-TRACKING ADJ. STRAC
38 H-BLK PULSE ADJ. HBLK
39 DC-TRANS POINT ADJ. DCT-P
40 DC-TRANS RATE ADJ. DCT-R
41 DC-TRANS LIMIT ADJ. DCT-L
42 B.S.P. LIMIT BSPL
43 B.S. POINT1 BSP1
02H:30H 03H:13H
IC Data setting Initial value
∗
PDC V-AMPLITUDE
PDC V-LINEARITY
PDC V-S CORRECTION
VCD1 V-PHASE
VCD1 H-PHASE
PDC H-SIZE
PDC EW-PARABOLA
PDC V-BIAS
PDC V-∫CORRECTION
PDC EW-CORNER
PDC TRAPEZIUM
PDC V-COMPENSATION
PDC H-COMPENSATION
SECAM BELL FILTER
SECAM R-Y
SECAM B-Y
SECAM SGP
SECAM C-ATT
SECAM ID-SENS
VCD1 FLESH
VCD1 SRT-MD
VCD1 WPDL
VCD1 WP-DET
VCD1 HI-BRT
VCD1 Y-γ
VCD1 COLOUR-γ
VCD1 CDE
VCD1 GP-PHASE
VCD1 R-Y PHASE
VCD1 R-Y PHASE
VCD1 R-Y GAIN
VCD1 G-Y GAIN
VCD1 P/N-ID
VCD1 Y-DLY
VCD1 VM-PHS
VCD1 S-TRAC
VCD1 H-BLK
VCD1 DC-TRANS POINT
VCD1 DC-TRANS RATE
VCD1 DC-TRANS LIMIT
VCD1 B.S.P. LIMIT
VCD1 B.S. POINT1
4-2
∗
73
22
9
7
17
42
33
5
10
5
30
6
4
120
8
8
0
0
0
1
0
1
0
1
1
2
1
0
1
1
0
2
1
0
0
0
0
2
6
0
0
5