TP-Link AV1000 User Manual page 2

werline network using the Pair button on two devices at a time.
in the powerline devices near each other when pairing.
1 Press the Pair button on any of the powerline devices
for 1 second. Its Power LED
owerline network:
Note: If the Power LED does not blink, press the Pair button again.
2 (
he powerline devices
device for 1 second. Its Power LED
should start blinking.
blinking.
ress the Pair button again.
3 When the Powerline LED
- TL-PA7017 KIT (European version) is used for demonstration in this guide.
line Network by Pairing (Recommended
- Images may differ from your actual product.
network has been successfully created.
Powerline Network by Pairing (Recomm
ED should start
To join an existing secure powerline network:
ts up, a powerline
k using the Pair button on two devices at a time.
created.
werline network using the Pair button on two devices at a time.
e devices near each other when pairing.
1 Press the Pair button on any of the existing powerline
in the powerline devices near each other when pairing.
devices for 1 second. Its Power LED
network:
cure powerline network:
Note: If the Power LED does not blink, press the Pair button again.
owerline network:
2
evices
he existing powerline
powerline adapter for 1 second. Its Power LED
nking.
he powerline devices
LED starts blinking.
starts blinking.
should start blinking.
n again.
ress the Pair button again.
3 When the Powerline LED
ress the Pair button again.
start
Its Power LED
ED should start
Router
ne
ns on, it's done.
ts up, a powerline
created.
erline network:
cure powerline network:
werline
Q1. How do I reset my powerline adapter?
blinking.
he existing powerline
A. With the powerline adapter plugged into an electrical outlet, press and hold
n again. LED starts blinking.
ress the Pair button again.
momentarily and then comes back on.
adapter?
Its Power LED
to an electrical outlet, press and hold
A1. Try another wall socket and make sure all powerline devices are on the same
electrical circuit.
.
ns on, it's done.
Powerline Device
instructions.
A3. If the problem persists, contact our Technical Support.
Adapter
TL-PA7017
Existing
Powerline Device
Existing
Existing
Powerline Device
should start blinking.
should start
lights up, a powerline
Blinking
starts blinking.
Adapter
TL-PA7017
turns on, it's done.
Blinking
Within 2 minutes
Blinking
Blinking
Within 2 minutes
not, pair all devices again.
A3. Make sure all devices are correctly and securely co
A4. Check if you have an internet connection by conne
the modem or router.
. Refer to the section above for
Set Up a Secu
Within 2 minutes
You can create or join a secu
Tip: We recommend that yo
To create a secur
1 Press the Pair button on a
More: To add additional
Powerline adapters and
Wait until the Powerline LED for 1 second. Its Power LE extenders with the default
turns on. settings, simply plug them
Note: If the LED is off, please
into the wall sockets on the
Note: If the Power LED does not
refer to FAQ-Q2
same electrical circuit.
2 (
device for 1 second. Its Po
blinking.
3 When the Powerline LED
network has been succes
Blinking
Within 2 minutes
Within 2 minutes
To join an existing
1 Press the Pair button on a
devices for 1 second. Its P
Note: If the Power LED does not
2
powerline adapter for 1 se
starts blinking.
3 When the Powerline LED
Blinking
Within 2 minutes
New
Powerline Device
Q1. How do I reset my powe
A. With the powerline adapter plu
Set Up a Secu
You can create or join a secu
Tip: We recommend that yo
To create a secur
Set Up a Secu
1 Press the Pair button on a
for 1 second. Its Power LE
Note: If the Power LED does not
You can create or join a secu
2 (
Tip: We recommend that you
device for 1 second. Its Po
Blinkin
blinking.
To create a secure
3 When the Powerline LED
Existing
network has been succes
1 Press the Pair button on an
Powerline Device
for 1 second. Its Power LE
Note: If the Power LED does not
To join an existing
2 (
device for 1 second. Its Po
1 Press the Pair button on a
blinking.
devices for 1 second. Its P
New
Powerline Device
Note: If the Power LED does not
3 When the Powerline LED
network has been succes
2
powerline adapter for 1 se
starts blinking.
To join an existing
3 When the Powerline LED
1 Press the Pair button on an
devices for 1 second. Its P
Note: If the Power LED does not
not,
2
powerline adapter for 1 se
A3. Mak
starts blinking.
A4. Che
3 When the Powerline LED
the
are lit on all of yo
Q1. How do I reset my powe
A. With the powerline adapter plu
Q4. Wh
momentarily and then comes b
not
A1. Try a
New
Powerline Device
A1. Try another wall socket and ma
electrical circuit.
A3. Che
On
Bli