Download Print this page

Advertisement

Quick Links

All of Discovery's Bunkbeds were designed and manufactured with your child's safety as our top priority. Their
unparalleled strength is a bi-product of the safety design. Our bunks meet all compliance with ASTM F 1427-07
"Standard Consumer Safety Specification for Bunk Beds" and Code of Federal Regulations (CFR)1213 "Safety Standards
for Entrapment Hazards in Bunk Beds" and (CFR) 1513 "Requirements for Bunk Beds".
Safety is a cooperative effort between us as the manufacturer, and you as aguardian. Please read and consider the warnings listed
below when choosing a mattress and discussing rules of use with your child.
SAFETY WARNINGS
1. Follow the information on the warnings appearing on the upper bunk end structure and on the carton.
Donotremovewarninglabelfrombed.
2. Always use the recommended size mattress or mattress support, or both, to help prevent the
likelihood of entrapment or falls.
3. Surface of mattress must be at least 5inches(127mm)below the upper edge of guardrails.
4. Do not allow children under6 years of age to use the upper bunk.
5. Prohibit more than one person on the upper bunk.
6. Periodically, check and ensure that the guardrail,ladder,and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10.Use of a nightlight may provide added safety precaution for a child using the upper bunk.
11.Always use guardrails on both long sides of the upper bunk.If bunk bed will beplaced next to the
wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent
entrapment between the bed and wall.
12.The use of water or sleep flotation mattresses is prohibited.
13. Keep these instructions for future reference.
STRANGULATION HAZARD –Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts and
jump ropes.
SIZE OF MATTRESS AND FOUNDATION
Use only mattress, foundation and deck combined which is 74-75 inches long and 37½-38½ inches
wide on upper bunk.
Ensure thickness of mattress and foundation combined does not exceed 9inches and mattress and is at
least 5 inches below upper edge of guardrails.
******Replacement parts, including additional guardrails, may be obtained from any Discovery dealer or
directly from us at the below address.
SAFETY FIRST!!!!!
2914 Mission Stair Stepper Bunk Bed
Patent # US 7,832,031 B1
Page 1
915 Cornwall Road
Sanford, Fl 32773

Advertisement

loading
Need help?

Need help?

Do you have a question about the 2914 and is the answer not in the manual?

Questions and answers

Summary of Contents for Discovery Telecom 2914

  • Page 1 Page 1 SAFETY FIRST!!!!! 2914 Mission Stair Stepper Bunk Bed All of Discovery’s Bunkbeds were designed and manufactured with your child’s safety as our top priority. Their unparalleled strength is a bi-product of the safety design. Our bunks meet all compliance with ASTM F 1427-07 “Standard Consumer Safety Specification for Bunk Beds”...
  • Page 2 Stair Stepper Bed Left Side Facing Page 2 *For Right side facing go to page 11 Tool required Number 3 Phillips screw driver 3 1/2” 1” 4” 3 1/2” 1 3/4” 3 1/2” 3 1/2” 3 1/2” 2” 1 1/4”...
  • Page 3 Page 3 Chest shell Short Post...
  • Page 4 Page 4...
  • Page 5 Page 5 REMINDER Important note If you want the Stair on the Remove shipping blocks right side please go to page 11 and save screws for next step Tall posts located Install tall posts in rail box #3 Front post Back post Check stamp under the post...
  • Page 6 Page 6 Phillips head screw, use screw driver.
  • Page 7 Setup top bed Page 7 no dowel on this side repeat on all 4 corners no dowel on this side Install Slat kit Always start assembling slat Hardware in Slat kit box kit flush with cleat...
  • Page 8 DropTop Bed in Place Page 8 Install Slat kit Hardware in Slat kit box...
  • Page 9 Page 9 Install Back Panel Use Phillips head screw on this side Mount magazine rack...
  • Page 10 Page 10 OPTIONAL Pre-Assembled 3 Drawer Unit, Simply Slide UnderThe Bunk Shown With Optional Full Extension Kit...
  • Page 11 Page 11 To Install stair case on the right side follow these steps Remove both post and Remove shipping block transfer it to this side Instal tall postl Remove Drawers...
  • Page 12 Page 12 Slide Chest out Remove Magazine Rack Turn chest around and slide it back in Slide Drawers back in...
  • Page 13 Setup top bed Page 13 Make sure that the opening is on the right side as shown Insert Magazine Rack back in and screw it in place Install slat kit Always start assembling slat kit flush with cleat Install slat kit, hardware in slat box...