Download Print this page
Discovery Telecom 1012 Manual

Discovery Telecom 1012 Manual

Stair stepper bunk bed

Advertisement

Quick Links

All of Discovery's Bunkbeds were designed and manufactured with your child's safety as our top priority. Their
unparalleled strength is a bi-product of the safety design. Our bunks meet all compliance with ASTM F 1427-07
"Standard Consumer Safety Specification for Bunk Beds" and Code of Federal Regulations (CFR) 1213 "Safety Standards
for Entrapment Hazards in Bunk Beds" and (CFR) 1513 "Requirements for Bunk Beds".
Safety is a cooperative effort between us as the manufacturer, and you as a guardian. Please read and consider the warnings listed
below when choosing a mattress and discussing rules of use with your child.
SAFETY WARNINGS
1. Follow the information on the warnings appearing on the upper bunk end structure and on the carton.
Do not remove warning label from bed.
2. Always use the recommended size mattress or mattress support, or both, to help prevent the
likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 inches (127 mm) below the upper edge of guardrails.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on the upper bunk.
6. Periodically, check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10. Use of a nightlight may provide added safety precaution for a child using the upper bunk.
11. Always use guardrails on both long sides of the upper bunk. If bunk bed will be placed next to the
wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent
entrapment between the bed and wall.
12. The use of water or sleep flotation mattresses is prohibited.
13. Keep these instructions for future reference.
STRANGULATION HAZARD–Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts and
jump ropes.
SIZE OF MATTRESS AND FOUNDATION
Use only mattress, foundation and deck combined which is 74-75 inches long and 37 ½-38 ½ inches
wide on upper bunk.
Ensure thickness of mattress and foundation combined does not exceed 9 inches and mattress and is at
least 5 inches below upper edge of guardrails.
******Replacement parts, including additional guardrails, may be obtained from any Discovery dealer or
directly from us at the below address.
SAFETY FIRST !!!!!
1012 / 7012 / 2112 Stair Stepper Bunk Bed
Patent# US 7,832,031 B1
915 Cornwall Road
Sanford, Fl 32773

Advertisement

loading
Need help?

Need help?

Do you have a question about the 1012 and is the answer not in the manual?

Questions and answers

Summary of Contents for Discovery Telecom 1012

  • Page 1 SAFETY FIRST !!!!! 1012 / 7012 / 2112 Stair Stepper Bunk Bed All of Discovery’s Bunkbeds were designed and manufactured with your child’s safety as our top priority. Their unparalleled strength is a bi-product of the safety design. Our bunks meet all compliance with ASTM F 1427-07 “Standard Consumer Safety Specification for Bunk Beds”...
  • Page 2 Stair Stepper Bed Left Side Facing *For Right side facing go to page 10 Tool required Number 3 Phillips screw driver 3 1/2” 1 1/4” 4” 1” 3 1/2” 3 1/2” 1 3/4” 3 1/2” 3 1/2” Page...
  • Page 3 No dowel on this side Bottom bed rails Top bed rails Page No dowel on this side...
  • Page 4 REMINDER Important note If you want the Stair on the Remove shipping blocks right side please go to page 10 and save screws for next step Tall posts located Install tall posts in rail box #3 Back post Front post Check stamp Check stamp under the post...
  • Page 5 Page Phillips head screw, use screw driver.
  • Page 6 No dowel on this side Page...
  • Page 7 Setup Top Bed Install Slat kit Always start assembling slat kit flush with cleat Page...
  • Page 8 Drop Top Bed in Place Page...
  • Page 9 Install Back Panel Use Phillips head screw on this side Mount magazine rack Page...
  • Page 10 Install Bottom Slat Kit OPTIONAL Pre-Assembled 3 Drawer Unit, Simply Slide Under The Bunk Shown With Optional Full Extension Kit Page...
  • Page 11 To Install stair case on the right side follow these steps Remove both post and Remove shipping block transfer it to this side Page Install tall post Remove Drawers...
  • Page 12 Slide Chest out Remove Magazine Rack Turn chest around and slide it back in Page Slide Drawers back in...
  • Page 13 Setup top bed Make sure that the opening is on the right side as shown Install Slat kit and guard rail support Insert Magazine Rack back in and screw it in place Always start assembling slat kit flush with cleat Page...

This manual is also suitable for:

70122112