Related Manuals for FarmTek 105356
Summary of Contents for FarmTek 105356
- Page 1 CHICK-INN LAYING NEST 105356 10-Hole Chick-Inn Laying Nest ©2010 FarmTek ® All Rights Reserved. Reproduction STK# Description is prohibited without permission. 105356 10-Hole Chick-Inn Lying Nest Revision date: 10.22.10...
-
Page 2: Safety Precautions
CHICK-INN LAYING NEST READ THIS DOCUMENT BEFORE YOU BEGIN TO CARE AND MAINTENANCE ASSEMBLE THE CHICK-INN LAYING NEST. • Periodically check fasteners to ensure they are tight Thank you for purchasing this Chick-Inn Laying Nest. and secure. When properly assembled and maintained, this product •... - Page 3 CHICK-INN LAYING NEST Left Panel ATTACH LOWER FRONT PANEL NOTE: There are different panel types. Panels with square holes and panels without. Panels with notches and panels without. Note location of each panel in all the photos. Front Panel Center with Notches Position the angled edges of the left and right Panel...
- Page 4 CHICK-INN LAYING NEST Panel with Notches ATTACH UPPER FRONT PANEL Position the upper front panel with square holes onto the assembly. Secure in place using twelve (12) machine screws and hex nuts. Note the location of the front panel; install the lip of the panel toward the top of the nest.
- Page 5 CHICK-INN LAYING NEST Panel without Notches Panel with Notches ATTACH BACK PANELS 1. Carefully flip nest over so the back side faces up. 2. Attach panels to the back of the assembly using the same procedure as the front panels using the remaining panels.
- Page 6 CHICK-INN LAYING NEST ATTACH TOP Attach the top to the assembly using the ten (10) machine screws and hex nuts. ATTENTION: Do not install a machine screw into the corner holes. Corner holes are used to install the hanging brackets in the following step. Machine screw heads go to the outside of the laying nest.
- Page 7 CHICK-INN LAYING NEST Bracket Bracket INSTALL HANGING BRACKETS Attach hanging brackets to the outer corners using 1/2" machine screws and hex nuts. Position screw heads to the outside. Parts List and Tools Required Socket/Wrench Set Flat Screwdriver 10-24X1/2 machine screws (6) Hanging Brackets (2) &...
- Page 8 CHICK-INN LAYING NEST ATTACH SUPPORT BRACKETS Short Support Attach the support brackets using the holes Bracket on the inside partitions and the supplied machine screws and locknuts. Install the long support brackets on the lower Long Support section of the assembly; install the short Bracket support brackets on the upper section.
- Page 9 CHICK-INN LAYING NEST ATTACH PERCHES Attach the perches to the support arms using 1-1/2" machine screws and hex nuts. Parts List and Tools Required Socket/Wrench Set Perches (3) 1/4-20 x 1-1/2 machine screws (12) & 1/4-20 hex nuts (12) *Items not to scale. Revision date: 10.22.10...
- Page 10 CHICK-INN LAYING NEST INSERT THE NEST BOTTOMS Next, insert one (1) nest bottom into each compartment. Position beveled edges against the sides of the nest. Gently push the nest bottom down into place. Parts List and Tools Required *Item not to scale. Nest Bottoms (10) Revision date: 10.22.10...
- Page 11 CHICK-INN LAYING NEST Parts List Hardware Pack Contents Description 10-24 x 1/2 Machine Screw 10-24 Hex Nut Left Side & Center Panels 1/4-20 x 1-1/2 Machine Screw Right Side Panel 1/4-20 Flange Nut Perch Hanging Brackets Short Support Brackets Long Support Brackets Back Panel with Notches Front Panel with Notches Back Panel without Notches...