Related Manuals for FarmTek Growers Supply HydroCycle Vertical Aeroponic Systems
Summary of Contents for FarmTek Growers Supply HydroCycle Vertical Aeroponic Systems
- Page 1 HydroCycle Vertical Aeroponic Systems ©2018 Growers Supply *Actual system may differ from system shown. All Rights Reserved. Reproduction 113593 8' Vertical System (44 Grow Sites) is prohibited without permission. Revision date: 09.21.18...
- Page 2 Important Information READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE YOUR HYDROCYCLE VERTICAL AEROPONIC SYSTEM. This guide provides helpful hints and important information needed to safely assemble and properly maintain the HydroCycle Vertical Aeroponic System. Read and understand this guide before you begin. SAFETY PRECAUTIONS TOOLS BASIC CARE AND MAINTENANCE...
- Page 3 Important Information PICTORIAL GUIDE Use the following graphics and photos to identify system parts. WF3375 WF3316 WF4065 WF1540 WF1390 LJ2502 LJ2502 WF2190 WF2193 111045 WF1570 WF3420 WF4790 Key 110077 Air Stone Punch 113696 WF8582 112710 113595 112689 Revision date: 09.21.18 113593...
- Page 4 Important Information PICTORIAL PARTS GUIDE—CONTINUED PVC PRIMER & PVC CEMENT Follow all directions printed on pvc primer and cement containers. Purple color of primer does not fade! Use caution during application to reduce spills and over WF6990 application at joints. PVC Cement Prime all joints before 113372 Purple...
- Page 5 Basic Aeroponic System The aeroponic system is ideal for growing in tight spaces. Multiple systems System shown for example only. arranged in the same area allow for maximum use of available growing space. Actual system may differ. However you decide to use your aeroponic system, review the information that follows to better understand how to prepare and setup and system.
- Page 6 Assembly Instructions—Reservoir Preparation DRILL RESERVOIR AND INSTALL BULKHEAD FITTING 1. Take the reservoir and locate the smooth surface on the outside at one end. WF8582 2. Using a 2-1/4" hole saw bit and drill, drill the hole for the bulkhead fitting. Clean debris from around hole and inside reservoir.
- Page 7 Assembly Instructions—Reservoir Cover Preparation DRILL DRAIN AND AIR LINE HOLES IN COVER Drill 1-3/8" to 1-1/2" Drill two 5/16" air tube drain hole here. holes in either location. Complete these steps: 1. Take the 113797 cover and set on customer-supplied supports for drilling drain hole.
- Page 8 Assembly Instructions—Air Pump & Air Stones 110077 Air ATTACH THE AIR PUMP AND AERATOR STONES Stone For optimal system performance and to extend the life of the nutrient solution through increased oxygenation, an aerator pump and aerator stones are included. Position stones on bottom of Attach 110091 reservoir opposite main pump.
- Page 9 Assembly Instructions— Prepare Grow Tube INSTALL SEALS, GROMMETS, AND DRAIN EXTENSION Complete these step: 112710 113595 1. Install all 112710 uniseals in the 10" grow tube. When installed correctly, seals will seat tightly against the outer surface of grow tube. 2.
- Page 10 Assembly Instructions—Assemble Grow Tube STEP 1 SET RESERVOIR AND ASSEMBLE GROW TUBE Complete these steps: 1. Take the 113112 mist column and carefully twist the 113107 cap with grommet (previous procedure—Step 2) onto threaded fitting at top. ATTENTION: Inspect the mist column to ensure that no mist emitters are damaged or missing.
- Page 11 Assembly Instructions—Assemble Grow Tube STEP 6 SET RESERVOIR AND ASSEMBLE GROW TUBE—continued 6. With assistance, take the grow tube and carefully slide cap and mist column assembly into tube. 7. Work the cap over the end of grow tube and tap in place with palm of your hand.
- Page 12 Assembly Instructions—Install 111045 Elbows in Grow Tube INSTALL 111045 ELBOWS IN GROW TUBE Once grow tube is assembled, install all 111045 elbows. Wet end of 111045 elbow and insert it into 112710 uniseal. Install all elbows so open end points up and away from drain extension end of tube. 111045 ATTENTION: Seat elbow tight against uniseal to prevent leaks.
- Page 13 Assembly Instructions—Set Grow Tube on Tower Stand SET GROW TUBE ON TOWER STAND Take the necessary steps to assemble tower stand if this has not been completed yet. Read the following procedure to determine which part of tower stand to attach after tower is set in place.
- Page 14 Assembly Instructions—Install Pump and Plumbing and Connect to Grow Tube WF1570 WF3316 Elbow INSTALL PUMP AND PLUMBING WF1380 WF3420 With tower locked in tower stand, install plumbing from reservoir to top of grow tube WF2190 using components shown. The 1" pvc is cut to length during assembly. ATTENTION: Wrap all threaded fittings with thread tape before assembly.
- Page 15 OPERATIONAL AND MAINTENANCE INFORMATION General Operating Instructions General Cleaning and Maintenance Instructions After assembly, check system before operation. Complete these steps: For optimal performance and to increase yields, check and clean reservoir periodically. Time between maintenance and cleaning depends on growing 1.
- Page 16 OPERATIONAL AND MAINTENANCE INFORMATION Reservoir Cleaning and Maintenance Clean reservoir periodically to maximize plant growth and to minimize system contamination. Steps that follow can be used to pump reservoir for cleaning and typical maintenance. Cleaning filter is strongly recommended after cleaning reservoir. ATTENTION: SYSTEM SHOWN MAY DIFFER 112066 FROM ACTUAL SYSTEM.
- Page 17 OPERATIONAL AND MAINTENANCE INFORMATION Clean Filter Screen and Housing ATTENTION: SYSTEM SHOWN DIFFERS FROM ACTUAL SYSTEM. Clean filters ensure proper flow. Filters should also be cleaned after cleaning FILTER ASSEMBLY IS THE SAME. STEPS FOR CLEANING THE reservoir to remove sediment. When a reduced flow rate or drop in pressure is FILTER ARE THE SAME.
- Page 18 REPLACE DAMAGED OR BROKEN MIST EMITTER Replace Damaged or Broken Mist Emitter In rare instances, a mist emitter may become damaged during shipping or installation. 110829 WF4790 Key WF4065 The 110829 drill & tap combo pak is included to easily repair a broken or damaged Drill &...
- Page 19 PAGE RESERVED FOR CUSTOMER NOTES AND RECORDS Revision date: 09.21.18 113593...
- Page 20 AeroTower Stand Part Locations STAND ASSEMBLY Use information on the following two pages to assemble stand for aeroponic plant tower. ITEM NO. PART NUMBER QTY. DESCRIPTION 115029 AEROTOWER STAND LEG 115030 AEROTOWER STAND UH SUPPORT 1 115031 AEROTOWER STAND UH SUPPORT 2 115032 AEROTOWER STAND UH SUPPORT 3 115033...
- Page 21 AeroTower Stand Connection Details NOTE: TOWER WILL BE CENTERED ON BASE OF AEROTOWER STAND 4 " 2 " & LEG TO LOWER SUPPORT RING ASSEMBLED HORIZONTAL SUPPORTS & 2 " 4 " VERTICAL SUPPORT LEG TO UPPER TO SUPPORT RING HORIZONTAL SUPPORTS CENTERING TOWER ONTO STAND NOTE: TOWER WILL BE TEK SCREWED TO...