i3 International Ax57R User Manual

2/5MP Infrared Mini Outdoor IP Dome Camera with T-Grip
Thank you for purchasing i3 International's Ax57/77R mini IP dome camera.
Ax57R2 is equipped with a fixed 2.8mm @ F1.8 lens. Ax57R4 and Ax77R2 are equipped
with a fixed 2.8mm and 4.0mm @ F2.0 lens, respectively.
This camera series features pre-installed T-bar ceiling clip (T-Grip) for easy one-hand
installation on most Standard 1" drop-ceiling grid types.
SAFETY
When installing your Ax57/77R camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light and unstable light sources
• temperatures below -20° C (-4° F) and above 50° C (122° F
To avoid electrical shock and to preserve the product warranty, DO NOT disassemble the
camera. Refer servicing to qualified personnel only.
POWER SUPPLY
This camera accepts PoE power.
Ensure the supplied voltage meets the power consumption requirements of this camera
before powering the camera on. Incorrect voltage may cause irreparable damage to the
video camera and will effectively void the camera warranty.
CLEANING
• For maximum optical clarity, the camera dome or lens must remain clean. Use a soft,
dry cloth to remove finger prints or dust from the dome cover.
• Use a blower to remove dust from the lens.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may dam-
age the surface finishes.
PACKAGE CONTENTS
Ensure that the items received match those listed on the order form and the packing slip.
In addition to this manual and a fully assembled camera, the dome camera packing box
includes:
A. Surface Mount template x1
B. Desiccant (attach to the inside of the Inner Liner) x1
C. Security torx bit x1
D. Round Head Screw (Tapping Type) x3
E. Plastic Anchor x3
F.
Standard RJ45 Connector x2
B C
Scan this QR code or visit ftp.i3international.com to view
and download AnnexxusConfigurationTool v1.5 (ACT) and
the full User Manual.
Contact our Technical Support team at: 1.877.877.7241 or
support@i3international.com if you have any questions
or concerns regarding camera installation or if you require
software services or support.
i3-TRNG-CAMS-Ax57R_77R.indd
).
3-Ø 4.5mm holes
(for plastic anchors)
Cable hole
Logo Direction A
D E F
QR Code for Complete
User Manual and ACT
User Manual
Ax57/77R
CAMERA PARTS AND DEFINITIONS
2
2
6
7
8
12
11
DEFAULT
1. T-Grip. Standard T-bar ceiling clip. See Drop-Ceiling Installation section for
more information.
2. Mounting holes (x3)
3. Dome cover
4. Screws securing the dome cover to camera module (x3, silver)
5. Dome bubble
6. Tilt bracket with two locking screws. Tilt to adjust lens angle and re-tighten
screws as needed when done.
7. IR board
8. Camera Lens Assembly. Pan to adjust lens angle.
9. Lens base. Rotate to adjust lens angle.
10. Camera lens.
11. Default pinhole. Press for 6 seconds to restore camera settings to factory
defaults.
12. Reset pinhole. Press for 1 second to reboot the camera.
13. MicroSD Card slot for on-camera video storage. (MicroSD card sold
separately).
14. RJ45 Ethernet PoE Port with waterproof RJ45 connector assembly.
Insert an Ethernet cable into the port for network connection as well as PoE
(Power over Ethernet) power. To maintain water-resistant rating in outdoor
installations, make sure to use the included waterproof RJ45 Connector
assembly.
111 mm
1
2
9
10
13
RESET
3
4
5
14