GE Spacemaker GSM2200V Dimensions And Installation Information page 3

GSM2200V
GE Spacemaker Under-the-Sink Dishwasher
®
Cabinet Rough-In Note: Either single- or
double-bowl sink may be used, centered
or offset, as shown in the front view
illustration.
The 20-1/2" maximum dimension from wall
to front of sink bowl must be accurate if
dishwasher is to fit properly under sink.
Water lines to sink faucet and drain from
sink can be run through area "A."
HOT WATER line to dishwasher is installed
in area "B."
Garbage disposer, water lines to faucet,
trap, waste air gap and water cutoff valve
are installed in 12" wide cabinet shown
in area "C." Sink opening for garbage
disposer must be dimensioned as shown in
front view, area "C" (7-1/2"). This will provide
clearance for the disposer and plumbing in
cabinet "C" when using double bowl sink.
If the sink bowl is more than 20-1/2"
maximum specified distance form the
wall, or if the base cabinet is less than the
24" minimum depth from the wall, a gap
between the tub front flange and the front
of the base cabinet may result.
Cabinet Rough-In Dimensions (in inches)
Countertop 1-1/2" MIN. thick
Countertop 1-1/2" MIN. thick
10-1/4" MAX.
A
10-1/4" MAX.
A
C
FRONT VIEW
FRONT VIEW
6" MAX.
B
6" MAX.
B
24 12"
MIN.
24
Cabinet Cut-Out for Sink Dimensions (in inches)
Sink
installation
cutout
8" x 20" Adjacent
cabinet rear cutout
5
Cabinet side
adjacent to D/W
FRONT VIEW
11-3/4
Cabinet cutouts for offset single and double
bowl sinks. Dishwasher not provided with
complete enclosure. Enclosures for sides,
top, bottom and back must be provided by
installer at time of installation.
installer at time of installation.
3/4" MIN.
3/4" MIN.
7-1/2
MIN. I.R.
7-1/2 34-1/4
± 1/4
34-1/4
C
± 1/4
Toe
kick
Toe
area
kick
area
Floor
Floor
Floor
12"
Floor
Wood Insert Cut-Out Dimensions (in inches)
MIN.
Wood Insert Cut-Out Dimensions (in inches)
GE/Hotpoint/RCA
GE/Hotpoint/RCA
Undersink Dishwasher Wood Insert Dimensions
(in inches)
Door insert
5
Door insert
Door insert
3-1/4
Access insert
Access insert
Access insert
12-1/2
23-9/16
Inserts must not
12
exceed 1/4" thickness When using GPF325
When using GPF325
within 5/16" of
1/4" custom dishwasher
1/4" custom dishwasher
edge around full
door and access panel kit.
door and access panel kit.
circumference.
When using GPF375
When using GPF375
3/4" custom dishwasher
3/4" custom dishwasher
door and access panel kit.
door and access panel kit.
Wall
20-1/2" MAX.
Wall
Sink bowl
1" MAX. to
20-1/2" MAX.
11" MIN sink flange
C L Sink bowl
1" MAX. to
Drain
sink flange
11" MIN
6" MAX.
C L
Drain
10-1/4" MAX.
A
Plumbing depth
6" MAX.
1-1/4"
10-1/4" MAX.
A
Plumbing depth
1-1/4"
11-3/4"
MIN. I.R.
MAX. Plumbing
11-3/4"
Dishwasher
MAX. Plumbing
SIDE VIEW
Dishwasher
Front of cabinet
SIDE VIEW
Flange
Front of cabinet
B
4" MAX.
Flange
Wood Insert Cut-Out Dime
B
4" MAX.
Dishwashers Installation
Dishwashers Installation
24"
GE/Hotpoint/RCA
(Pub. 1-G003 pg. 131B) May 12, 1993
min. cabinet
(Pub. 1-G003 pg. 131B) May 12, 1993
24"
min. cabinet
Door insert
Panel Thickness
A
Panel Thickness
A
3/4
18-7/8 3/4
Access insert
Front
Front
of
of
B
Panel
Panel
C
C
3-11/16
1-1/2
1-1/2
1/2
1/2
B
When using GPF325
B
1/4" custom dishwasher
door and access panel kit.
When using GPF375
3/4" custom dishwasher
door and access panel kit.
Specification Created 4/11
Either single- or double-bowl si
shown in the front view illustrat
Either single- or doub
to front of sink bowl must be ac
shown in the front vie
under sink. Water lines to sink
to front of sink bowl m
through area "A." HOT WATER
under sink. Water line
Garbage disposer, water lines
through area "A." HOT
cutoff valve are installed in 12"
Garbage disposer, wa
opening for garbage disposer m
cutoff valve are install
view, area "C" (7-1/2"). This wil
opening for garbage d
plumbing in cabinet "C" when u
view, area "C" (7-1/2"
more than 20-1/2" MAX. specif
D
plumbing in cabinet "C
cabinet is less than the 24" MIN
(Pub. 1-
more than 20-1/2" MA
tub front flange and the front of
cabinet is less than th
tub front flange and th
Panel Thic
A
3/
Front
of
Panel
C
1-1/2
1/2
1/4
1/4
Listed by
Underwriters
Laboratories
350518