GE ADW1000 Series Owner's Manual
Hide thumbs Also See for ADW1000 Series:


Safety Instructions

. . . . . . . . 2, 3

Operating Instructions

Care and Cleaning . . . . . . . . . . . . . .12
Control Panels . . . . . . . . . . . . . . . . . . .6
Control Settings . . . . . . . . . . . . . . 4-5
Dial Cycles . . . . . . . . . . . . . . . . . . . . . .7
Flashing Display Lights . . . . . . . . . . .8
Dishwasher Racks . . . . . . . . . . . . . .10
Loading Place Settings . . . . . . . . . .11
Optional Accessories . . . . . . . . . . . .12
Using the Dishwasher . . . . . . . . . .8, 9
Consumer Support
Consumer Support . . . . . Back Cover
Warranty . . . . . . . . . . . . . . . . . . . . . 15
Write the model and serial
numbers here:
Model # ____________________
Serial # ____________________
You can find them on a label on the
tub wall just inside the door.
. . . 13, 14
165D4700P343 49-55023-1
Owner's Manual
ADW1000 Series
GHDA300 Series
GSD1000 Series
GSD2000 Series
GSD3000 Series
GSD4000 Series
GSM2000 Series
HDA1000 Series
HDA2000 Series
HDA3000 Series
04-07 JR


Table of Contents

Summary of Contents for GE ADW1000 Series

  • Page 1: Table Of Contents

    ..2, 3 Owner’s Manual Operating Instructions ADW1000 Series Care and Cleaning ....12 GHDA300 Series Control Panels ....6 GSD1000 Series Control Settings .
  • Page 2: Save These Instructions

    This dishwasher must be properly installed and located in accordance with the Installation Instructions before it is used. If you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by visiting our website at I Connect the dishwasher/appliance to a grounded I Do not attempt to repair or replace any part metal, permanent wiring system;...
  • Page 3 ® to the possibility of small fingers being pinched in been approved for use in all GE dishwashers. the door. I Locate sharp items so that they are not likely I Do not discard a dishwasher without first removing to damage the door seal.
  • Page 4: Control Settings

    About the dishwasher control panel Control Settings Cycles An indicator light above the selected pad will be ON to indicate which CYCLE has been selected, on some models. POTS & PANS/ For heavily soiled dishes or cookware with dried-on or baked-on soils. Everyday dishes may be included. HEAVY WASH This cycle will not remove burned-on foods.
  • Page 5: Cycle Chart

    Control Settings Cycle Chart Model Cycle Water Usage (gal.) Cycle Time (min.) GSD1100 Hot Start Option Heavy Wash Normal Wash Rinse Only Plate Warmer HDA1100 Hot PreWash Option ADW1100 Normal Wash Drying GSD1300 Hot Start Option GSD2100 Heavy Wash...
  • Page 6: Control Panels

    About the dishwasher control panel You can locate your model number on the left tub wall just inside the door. Throughout this manual, features and appearance may vary from your model. Please match the control panel for your unit to a similar control panel below.
  • Page 7: Dial Cycles

    Operation of models with cycle dial Rinse Only For rinsing partial loads that will be washed later. Do not use detergent. Make sure HEATED DRY is not selected. Slowly turn the Dial to RINSE ONLY. Be sure the door is unlatched.
  • Page 8: Flashing Display Lights

    Operation of electronic models (model GSD4000 Only) Using the Dishwasher Door The door must be closed and locked into place to select a LOAD SELECTION or an OPTION. If the door is opened during a cycle and left open, the dishwasher will beep once every 30 seconds until the door is closed and latched into place.
  • Page 9: Proper Use Of Detergent

    Otherwise, the detergent cup will not close and latch Dishwashing Detergents have been approved for use properly. Add detergent then close the main cup. in all GE dishwashers. Keep your detergent fresh and Open cup dry. Don’t put powder detergent into the dispenser until you’re ready to wash dishes.
  • Page 10: Loading The Dishwasher Racks

    Loading the dishwasher racks For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets may vary from your model. Upper Rack Secure larger dishwasher-safe plastics over The upper rack is for glasses, cups and two fingers when possible.
  • Page 11: Loading Place Settings

    Loading place settings… Follow these guidelines for loading 10 place settings. Features and appearance of racks and silverware baskets may vary from your model. Upper Rack—10 place settings Upper Rack—10 place settings Lower Rack—10 place settings Upper Rack—12 place settings Upper Rack—12 place settings...
  • Page 12: Care And Cleaning

    GPF65 and install a 1⁄ 4″ thick decorative wood door: Consult your GE Appliance dealer to get the correct GPF25B (Black) GPF325B/GPF425B kit for your model. GPF25W (White) GPF325W/GPF425W...
  • Page 13: Troubleshooting Tips

    Stained tub interior Some tomato-based • Use of the RINSE ONLY cycle after adding the dish to the load foods can cause reddish can decrease the level of staining. GE recommends Cascade ® stains Plastic Booster to help remove these types of stains.
  • Page 14: Before You Call For Service

    Before you call for service… Problem Possible Causes What To Do Dishes don’t dry Low inlet water • Make sure inlet water temperature is at least 120°F. temperature • Select HEATED DRY. • Use HOT START and ADDED HEAT options. •...
  • Page 15: Warranty

    This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service location.
  • Page 16: Consumer Support

    Contact Us If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including your phone number, or write to: General Manager, Customer Relations...
  • Page 17 19" MIN. from wall 24" From wall For answers to your Monogram, GE Profile ® ™ ® appliance questions, visit our website at or call GE Answer Center service, ® 24" MIN. 800.626.2000. As an EnErgy StAr ® Listed by...
  • Page 18 GSD2300/2301N Built-In Dishwasher ® Features and Benefits • Meets 2007 ENERGY STAR® Criteria - Can reduce utility bill by using less water to get dishes clean • 4-level PowerScrub™ wash system - Four wash levels quietly and efficiently scrub dishes clean •...
  • Page 19: Installation Instructions

    GE Consumer & Industrial Appliances Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: BEFORE YOU BEGIN IMPORTANT – The dishwasher MUST be STOP installed to allow for future removal from the Read these instructions completely and enclosure if service is required.
  • Page 20: Air Gap

    PARTS SUPPLIED IN INSTALLATION Screw Kit PACKAGE: Hex Head Phillips Head Two 8-18 x 5/8" Phillips head wood screws ■ Junction Box Screw Wood Screws Junction box cover and #10 hex head 1/2" long ■ 5/8" long ������������� Junction Box Cover screw ������������...
  • Page 21: Prepare Dishwasher Enclosure

    Installation Preparation–Enclosure PREPARE DISHWASHER ENCLOSURE • The dishwasher must be installed no more than 10 feet from sink for proper drainage. WARNING • The dishwasher must be fully enclosed on the top, To reduce the risk of shock, fire, or injury sides, and back.
  • Page 22 Installation Preparation–Drain METHOD 1–Air Gap with Waste Tee or Disposer PREPARE DRAIN PLUMBING Drain Requirements • Follow local codes and ordinances. • Drain hose must not exceed 10 feet in length. • A high drain loop or air gap is required. See below. Drain Method Figure C The type of drain installation depends on the...
  • Page 23 Installation Preparation–Electrical Supply PREPARE ELECTRICAL WIRING Alternate WARNING Receptacle FOR PERSONAL SAFETY: Remove house Location fuse or open circuit breaker before 18" beginning installation. Do not use an 1-1/2" Dia. Hole (Max.) extension cord or adapter plug with this Receptacle Location 18"...
  • Page 24 Installation Preparation–Hot Water Supply PREPARE HOT WATER SUPPLY CAUTION Hot Water Line • The line may enter from either side, rear, or floor The hot water supply line pressure must be at least 20 PSI. Lower pressures could cause the water valve to leak and within the shaded area shown in Figure F.
  • Page 25: Dishwasher Installation

    Dishwasher Installation STEP 3: REMOVE WOOD BASE CAUTION IMPORTANT – Do not kick off wood base! Do not remove the wood base until you are ready to Damage will occur. install the dishwasher. The dishwasher will tip over when the door is opened if the base is removed. •...
  • Page 26 The power cord and connections must comply with the National Electrical Code, Section 422 and/ or local codes and ordinances. Maximum power cord length is 6 feet. Power Cord Kit WX09X70910, available for purchase from an authorized GE Water Valve Appliance Dealer, meets these requirements. Bracket 90°...
  • Page 27 78" long. If a longer hose is needed, a 10 foot long hose may be purchased from an CORD, IF USED, THROUGH CABINET authorized GE appliance dealer. The 10 foot long • Upright the dishwasher and position it in front of hose is part number GPF10S.
  • Page 28 Dishwasher Installation STEP 11: SLIDE DISHWASHER INTO CABINET STEP 12: POSITION AND LEVEL DISHWASHER IMPORTANT – Do not push against the front IMPORTANT – Dishwasher must be level for panel with knees. Damage will occur. proper dish rack operation, wash performance, and door operation.
  • Page 29 Dishwasher Installation STEP 13: FASTEN DISHWASHER TO STEP 14: CONNECT WATER SUPPLY UNDERSIDE OF COUNTERTOP OR SIDES Connect the water supply line to the 90° elbow OF CABINET installed in Step 6. • Slide the compression nut and then the ferrule over In this step you will need the two 5/8"...
  • Page 30 Dishwasher Installation STEP 15: CONNECT DRAIN LINE Method 1 – Air gap with waste tee or disposer The molded end of the drain hose will fit 5/8" through 1" diameter inlet ports on the air gap, waste tee or disposer. •...
  • Page 31 Dishwasher Installation STEP 16: CONNECT POWER SUPPLY STEP 17: INSTALL JUNCTION BOX COVER If a power cord with plug is already installed, If junction box cover is already installed, skip to proceed to Step 17. Step 18. If the dishwasher came with a factory-installed In this step you will need the junction box cover and power cord and you want to convert it to a the #10 hex head screw from the screw kit set aside...
  • Page 32 Dishwasher Installation STEP 19: DISHWASHER WET TEST – Check the electrical connection to the water valve. The red electrical connector should be CHECK LIST plugged into the dishwasher water valve. If it is Turn on power supply or if power cord is used, ■...
  • Page 33 Dishwasher Installation STEP 20: REPLACE ACCESS PANEL AND STEP 21: LITERATURE TOEKICK Leave the Owners’ Manual, Installation ■ In this step you will need the panels and the two Instructions, samples, and/or coupons with screws set aside in Step 4. consumer.
  • Page 34 • Return to Step 16 in these instructions to complete the conversion. Figure BB Figure CC Conversion Harness 06H-1949_Conversion Harness SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE GE Consumer & Industrial General Electric Company ������������������� Louisville, Kentucky 40225 Pub. No. 31-30218 Dwg. No. 206C1559P158 ND 06H-1949 (10/06)

Table of Contents