Maintenance; Daily, Weekly, Periodic; Condensate Hood Baffle And Air Diffusers - Accurex XBEW Installation, Operation And Maintenance Manual

Maintenance

Daily Maintenance
L/4
1. Wipe grease from exposed metal surfaces on the
hood interior using a clean, dry cloth.
2. Visually inspect the filters for grease accumulation.
FIG. 9
3. Remove grease cups, empty contents and replace
cup.
Weekly Maintenance
1. Remove the grease filters and wash in dishwasher or
pot sink.
Note: Filters installed over heavy grease
producing equipment may require more frequent
cleaning. See Filter Washing Frequency Guide,
FIG. 13
page 32.
L (MODULE LENGTH)
2. Before replacing filters, clean the interior plenum L/4
L (MODULE LENGTH)
L/2
L/2
L/2
surfaces of any residual grease accumulations.
Periodic Maintenance
1. Painted hood exterior surfaces should be cleaned
with a mild detergent solution.
2. Stainless steel hood exterior surfaces should be
cleaned with a mild detergent and then polished with
FIG. 15
a good grade stainless steel polish to preserve the
original luster.
Note: Never use abrasive cleaners or chemicals
on hood surfaces. Never use chlorine based
cleaners or iron wool pads to clean the hood.
They may scratch or mar the material. Always rub
with the grain of the stainless.
3. To maintain optimum performance of your hood and
fan, duct cleaning should be performed as often as
31.25 INCH
the application and code requires.
CRITICAL
DIMENSION
4. Recaulk the hoods with an NSF Approved silicone
caulk, (GE SCS1009 or its equivalent) as needed.
5. Inspect the supply air discharge portion on external
supply plenums to ensure the airstream is free from
debris or other blockage.
Condensate Hood Baffle Installation,
Fig. 21 and 22 HOLE DRILLED
BY INSTALLER
1. Grasp the baffle with drain holes facing down and lift
1/4 INCH BOLT AND CAP NUT
SUPPLIED BY MANUFACTURER
into the hood. For short hoods with only one baffle, it
may be necessary to turn the baffle slightly diagonally
to fit it past the drain channel.
2. After the baffle clears the drain channel of the hood,
turn the baffle so it is lined up with the upper hanger
HEMMED EDGE
FIG. 23
in the hood.
3. Hook the upper channel of the baffle over the upper
hanger of the hood and set the lower edge of the
baffle into the condensate gutter. Repeat until all
baffles are installed in the hood.
HOOD END PANEL
4. Center the baffle from side to side in the hood.
FIG. 10
FIG. 14
FIG. 16
L/4
FIG. 16
FIG. 23
HOOD END PANEL
SLIDE FLANGE
BACKSPLASH PANEL
BEHIND BACK
OF THE HOOD
Fig. 21 - CORRECT
UPPER
HANGER
UPPER
HANGER
Fig. 22 - INCORRECT
UPPER
HANGER
UPPER
HANGER
Air Diffusers
The air diffusers, located at the bottom of the back
supply will need to be cleaned as often as the
application dictates. Inspect periodically to determine
the cleaning schedule.
1. To clean the air diffusers, unfasten the screws.
Remove the air diffusers from the back supply unit
and wash in the sink or dishwasher.
FIG. 53
2. Refasten with the stainless steel screws.
HOOD FRONT PANEL
Grease Grabber™ Filter Installation
Never install the second stage filter in the front filter
channel. The second stage filter must be installed
behind a UL Classified Grease-X-Tractor™ primary
SECTION VIEW
OF BACKSPLASH
filter.
PANEL OVERLAP
1. Slide the top edge of
the second stage filter
HOOD FRONT PANEL
into the top rear filter
channel; Fig. 23.
UPPER HANGER
UPPER HANGER
FIG. 17
REMOVABLE AIR DIFFUSERS
FIG. 54
NOTE
FIG. 53
Kitchen Hoods • Type I and Type II
UPPER HANGER
UPPER HANGER
CONDENSATE
GUTTER
CONDENSATE
GUTTER
UPPER HANGER
UPPER HANGER
CONDENSATE
GUTTER
CONDENSATE
FIG. 17
GUTTER
REMOVABLE A
FIG. 55
Fig. 23
27